cb-obs411 electrical mechanical data sheet - SE Spezial-Electronic ...

More documents

Recommendations

Info

connectBlue3 Electrical Interface and ConnectorsThis section describes the signals available on the module interface connectors. There are three ways to connect to the OEM Serial PortAdapter:Via the PCB solder pads on the edge of the PCB, J6 (see Figure 3). See Section " Using the J6 PCB solder pads" for moreinformation.Via the 2x20-pin 1mm pitch board-to-board (one piece part) connectors, J2 through J3. The J2 to J3 connectors on the OEMSerial Port Adapter exist on the module only as a mating PCB-layout pattern (see Figure 3). See Section "Using the J2/J3Board-to-Board Connectors" for more information.Optional: Via the JST connector, J8 (see Figure 4). The connector is a 6 poles wire connector. The pitch is 1mm. Themanufacturer of the mounted connector is JST and the part number is SM06B-SRSS-TB. The SM06B-SRSS-TB connector ismated with the wire connector SHR-06V-S from JST. Other connector options are also available from JST.Figure 3: The solder pads J6 are available on the long edges of the bottom side of the PCB. The board-to-board connector padsJ2-J3 are located between the mounting holes.Figure 4: The JST connector J8 is mounted on the component sida of the PCB as an option.Copyright © 2010 connectBlue AB Page 6 of 42
connectBlue3.1 Pin Numbering3.1.1 J2, J3 and J6 bottom side connectorsFigure 5: Bottom view of the PCB with the pin numbering of the J2, J3 and the J6 connectors.3.1.2 J8 JST connectorFigure 6: Top view of the PCB with the pin numbering of the J8 connector.Copyright © 2010 connectBlue AB Page 7 of 42
Page 1 and 2: connectBlueCB-OBS411 ELECTRICAL MEC
Page 3 and 4: connectBlue2 IntroductionThe hardwa
Page 5: connectBlue2.3 Block DiagramFigure
Page 9 and 10: connectBlue13 - 8 - GREEN/Switch-1
Page 11 and 12: connectBlueR IN_PULL-UPInput signal
Page 13 and 14: connectBlue5 Antennas5.1 Surface Mo
Page 15 and 16: connectBlue5.2.2 AntennasPart Numbe
Page 17 and 18: connectBluePartNumberNamecB-ACC-17R
Page 19 and 20: connectBlue6 Mechanics6.1 Module Ou
Page 21 and 22: connectBlueFigure 9: Host PCB layou
Page 23 and 24: connectBlueThe modules are produced
Page 25 and 26: connectBlueFor more information ple
Page 27 and 28: connectBlue8.3 FCC and IC Complianc
Page 29 and 30: connectBlue9 Guidelines for Efficie
Page 31 and 32: connectBlue10.2.1.2.2 Module output
Page 33 and 34: connectBlue10.2.2.2 External RS232
Page 35 and 36: connectBlueFigure 17: A complete RS
Page 37 and 38: connectBlueFigure 21: A red LED in
Page 39 and 40: connectBlueFigure 25: No restore sw
Page 41 and 42: connectBlueFigure 30: A reset switc

cb-obs411 electrical mechanical data sheet - SE Spezial-Electronic ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?