Classic Below Ground Supported Slab - Jablite

More documents

Recommendations

Info

VersatileJabfloor can be used above or below the damp-proof membrane.EnvironmentExpanded polystyrene has been awarded an A+ rating by the BRE’s Green Guide toSpecification.All-dry constructionThe use of Jabfloor with a chipboard finish provides an all-dry method of construction, saving up to one week insite time compared to a wet screed.TypeJabfloor is supplied as EPS 70,100, 150, 200 and 250 as defined in BS EN 13163. Flame retardant additivematerial is available to order.ApprovalsJabfloor has been assessed and approved by the British Board of Agrément for use above a concrete slab withtimber floor finishes; Certificate number 87/1796.DimensionsStandard size: 2400 x 1200mm.Standard thicknesses: 25, 30, 40, 50, 60, 75, 100, 120, 150 and 200mm (Other thicknesses available to order).FireSolid ground floors are not required to provide fire resistance. When properly installed, the EPS insulation is fullyprotected by the chipboard and will have no adverse effect on the fire performance of the floor. Euroclass E,flame retardant material, is available to order.U-valuesThe rate of heat loss through a ground floor varies with its size and shape. The thickness of insulation requiredto meet a given U-value will similarly depend on the size and shape of the floor. Approved Documents L1A , L1B,L2A and L2B guide you to BS EN ISO 13370 as the method for determining floor U-values based on the floorperimeter and floor area where:“P” is length of exposed perimeter in metres and “A” is floor area in square metres.The measurement of both the floor area and perimeter should be made on the internal finished surface of thewalls enclosing the heated space; unheated areas such as garages, porches and storage spaces need not beincluded. For buildings such as terraces or blocks of flats and apartments, the measurement should be takenover the total gross ground-floor area.U-values are based on the following k-values:l Jabfloor 700.038W/mKl Jabfloor 100 0.036W/mKl Jabfloor 150 0.035W/mKl Jabfloor 200 0.034W/mKl Jabfloor 250 0.034W/mKFloors | Walls | Roofs Jablite Claymaster Technical Information 4
2.0BELOW CHIPBOARD FINISHChipboard FinishVapour Control LayerConcrete SlabDamp-proof MembraneJabfloor ClassicU-value TablesU-VALUE: 0.25 W/m²KP/A Ratio Jabfloor 70 Jabfloor 100 Jabfloor 150 Jabfloor 200 & 2501.00 110 105 100 1000.90 105 100 100 1000.80 100 100 100 900.70 100 100 90 900.60 90 90 85 850.50 85 80 80 750.40 75 75 70 700.30 60 60 55 550.25 50 50 50 500.20 30 30 30 300.15 25 25 25 25Keystandard thicknesstwo layers of standard thicknessStandard thicknesses: 25, 30, 40, 50, 60, 75, 100, 120, 150, 200mmFloors | Walls | Roofs Jablite Claymaster Technical Information 5
Page 1 and 2: JabliteJabfloorClassicTechnicalInfo
Page 3: 1.0JABLITE JABFILLScreed FinishVapo
Page 7 and 8: U-VALUE: 0.15 W/M²KP/A Ratio Jabfl
Page 9 and 10: 2.1BELOW GROUNDSUPPORTED SLABConcre
Page 11 and 12: U-VALUE: 0.15 W/m²KP/A Ratio Jabfl
Page 13 and 14: 2.2BELOW SCREED FINISHScreedVapour
Page 17 and 18: 2.3PRECAST SUSPENDEDCONCRETE FLOORT
Page 23 and 24: The boards should be laid with stag
Page 25 and 26: InstallationSupportTo prevent movem
Page 27 and 28: Dimensional stabilityIn accordance
Page 29 and 30: TYPICAL PROPERTIES OF JABLITE INSUL
Page 31 and 32: 5.0SUSTAINABILITYJablite Insulation
Page 33 and 34: PentanePentane, a non-CFC expansion
Page 35: 6.1JABFLOOR CLASSIC 70DECLARATION O
Page 38 and 39: Thermal Resistance - Table 3Nominal
Page 40 and 41: Thermal Resistance - Table 3Nominal
Page 42 and 43: 3 HAZARDS IDENTIFICATIONHuman Healt
Page 44 and 45: Raised thresholds to doorways or bu
Page 46 and 47: 16 OTHER INFORMATIONUses and Restri
Page 48 and 49: Certificate No: FM 01260LocationJab
Page 50 and 51: Certificate No: EMS 559414LocationJ
Page 52 and 53: Vencel Resil LimitedInfinity HouseA

Classic Below Ground Supported Slab - Jablite

Create successful ePaper yourself

Delete template?

Save as template?