Concrete Pipe & Box Culvert Installation - Shaw Precast Solutions

More documents

Recommendations

Info

LUBRICATE GASKETLubricate the gasketthoroughly before it isplaced on the spigot ortongue.Excess force will berequired to push thepipe to the homeposition if gasket is notwell lubricated.INSTALL GASKETFit the gasket carefully.Equalize the rubbergasket stretch by runninga smooth, round object,inserted between gasketand spigot, around theentire circumferenceseveral times.Unequal stretch couldcause bunching ofgasket and may causeleaks in the joint orcrack the bell.American Concrete Pipe Association • www.concrete-pipe.org 41
ALIGN PIPEAlign bell and spigot ofpipes to be jointed. Beforehoming the joint, checkthat the gasket is incontact with the entrytaper around the entirecircumference.a guide and do not replace or supersede projectspecifications, contract documents, or specificmanufacturer’s recommendations.MasticMastic sealants consist of rubber compounds orbitumen and inert mineral filler, which are usuallyapplied at ambient temperatures. The joint surfacesare thoroughly cleaned, dried and prepared inaccordance with the manufacturer’s recommendations.A sufficient amount of sealant should be usedto fill the annular joint space with some squeezeout. During cold weather, better workability of themastic sealant can be obtained if the mastic andjoint surfaces are warmed.MortarImproper alignment candislodged gasketcausing leaks orpossibly break the bell.Mortar consists of portland cement paste, sand42American Concrete Pipe Association • www.concrete-pipe.org
Page 1 and 2: RESOURCE NO 01-103Concrete Pipe& Bo
Page 3 and 4: Joint Testing-Air..................
Page 5 and 6: PRE-CONSTRUCTIONPRECAUTIONSFederal
Page 7 and 8: the delivery document.If a pipe is
Page 9 and 10: LIFT HOLD DEVICEStenances, the lift
Page 11 and 12: INSTALLATIONLINE AND GRADEFor sewer
Page 13 and 14: construction is not considered to b
Page 15 and 16: invert and the string line. Special
Page 17 and 18: TRENCH WIDTH FOR CONCRETE PIPEPipe
Page 19 and 20: STANDARD INSTALLATIONSThrough consu
Page 21 and 22: STANDARD TRENCH / EMBANKMENT INSTAL
Page 23 and 24: HORIZONTAL ELLIPTICAL PIPESTANDARD
Page 25 and 26: ARCH PIPESTANDARD EMBANKMENT INSTAL
Page 27 and 28: UNSHAPED - A granular foundation wi
Page 29 and 30: EMBANKMENT BEDDING CIRCULAR PIPE(IN
Page 31 and 32: TRENCH BEDDING CIRCULAR PIPE(INCHES
Page 33 and 34: TRENCH BEDDINGS ELLIPTICAL &ARCH PI
Page 35 and 36: EMBANKMENT BEDDINGS ELLIPTICAL& ARC
Page 37 and 38: JOINTINGPlacement of pipe should st
Page 39: LUBRICATE BELLLubricate bell jointi
Page 43 and 44: JOINT PROCEDURESJoints for pipe siz
Page 45 and 46: develop the necessary controlled pu
Page 47 and 48: CURVED ALIGNMENTDeflected Straight
Page 49 and 50: FINAL BACKFILLINGOnce the envelope
Page 51 and 52: with the maximum density of a parti
Page 53 and 54: INFILTRATION TEST54American Concret
Page 55 and 56: EXFILTRATIONThe exfiltration test i
Page 57 and 58: should be measured from the same re
Page 59 and 60: AIR TEST60American Concrete Pipe As
Page 61 and 62: JOINT TESTING-AIRJoint testing acco
Page 63 and 64: II. BOX CULVERT INSTALLATION MANUAL
Page 65 and 66: • Design live load• Type of joi
Page 67 and 68: Gaskets and sealing materials shoul
Page 69 and 70: ally inspected for rocks, frozen lu
Page 71 and 72: BEDDINGS PRECAST CONCRETEBOX SECTIO
Page 73 and 74: and applied down the sidewall 12 in
Page 75 and 76: should be done uniformly. If the jo
Page 77 and 78: span or 3 ft. (1 m), whichever is l
Page 79 and 80: AASHTO M 273 (M 273M): Precast Rein
Page 81 and 82: Covers joints where infiltration or
Page 83 and 84: Sewer Pipe: Covers acceptance of pi
Page 85 and 86: ASTM C 1433 (C 1433M): Precast Rein
Page 87 and 88: sewer and its connections through p
Page 89 and 90: FEET HEAD OF WATERINTO PRESSURE, PO

Concrete Pipe & Box Culvert Installation - Shaw Precast Solutions

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?