Click for Instruction Manual - Nashbar

More documents

Recommendations

Info

Screen 1 (Figure 23)Displays current values for Power (watts), Speed, Slope, Trip Distance and Ride Time. The speed comparison arrows in the upper rightcorner of the screen compare current speed to average speed. An upward arrow indicates your current speed is above your averagespeed. A downward arrow indicates your current speed is below your average speed.A. Current PowerB. Current SpeedC. SlopeD. Trip DistanceE. Ride TimeF. Speed ComparisonScreen 2 (Figure 24)Displays average values for Power (watts), Speed and Slope. Also displayed are Trip Distance, Ride Time and Speed Comparison arrows.A. Average PowerB. Average SpeedC. Average SlopeD. Trip DistanceE. Ride TimeF. Speed ComparisonScreen 3 (Figure 25)Displays maximum values for Power (watts) and Speed, Elevation Gain, Total Distance (odometer) and Total Ride Time. Also displayed arethe Speed Comparison arrows. The Total Distance and Total Ride Time values represent total distance and time accumulated on all ridesto date, and will not be reset when the data screens are cleared (see Section C, “Reset”).A. Maximum PowerB. Maximum SpeedC. Elevation GainD. Total DistanceE. Total Ride TimeF. Speed ComparisonB. Battery Life IndicatorWhen battery life is low, a battery icon will flash in the display screen to indicate only a few hours of battery life remain. See Figure 26.When the battery icon appears, replace the transmitter batteries (in the resistance unit) and console batteries as soon as possible.C. ResetAt the beginning of each ride you’ll want to perform a reset to clear from memory the data from your previous ride.1. To clear the data, press and hold the SET button. After 3 seconds, “CLEAR” will be displayed (at this point no data has been deleted).Continue to hold the SET button and in another 3 seconds “DONE” will appear, indicating that all accumulated data (except TotalDistance and Total Ride Time) has been cleared from memory. See Figure 27.2. To reset Total Distance and Total Ride Time (as well as all other data), press and hold both the SET and MODE buttons. After 8 seconds“CLEAR” will be displayed (at this point no data has been deleted). Continue to hold the SET and MODE buttons, and in another 2seconds “DONE” will appear, indicating that all accumulated data has been cleared from memory.D. Auto OffAfter 2 minutes of inactivity (no pedaling or button presses) the system will automaticallyswitch off to prolong battery life. Current values will be maintained. To turn the system back on press either button (SET or MODE) or beginpedaling.E. Summary List of Ride Data4
Synchronizing Console and Resistance Unit:The handlebar console and resistance unit on your Watt Master Fluid Wireless Trainer have been linked so that the console receives onlycoded data transmitted from your resistance unit. This eliminates interference when you train with other riders using Watt Master trainers, orwhen you’re near another wireless device transmitting data on the same frequency.Should you ever need to re-establish the synchronization link between the console and resistance unit, follow the procedure below.1. Remove the resistance unit from the spring plate (C).2. Remove the cap at the top of the tube on the underside of the resistance unit. See Figure 31. Inside the tube is a small button.3. If your handlebar console has a power switch, turn it to the “off” position. If your console does not have a power switch, wait 2 minutes forthe console to enter sleep mode.4. Now turn the console on again, either by moving the power switch to the “on” position or by pressing the SET or MODE button.5. Once the computer is turned on, depress the small button inside the tube on the underside of the resistance unit TWICE within 15 seconds.If you can’t reach the button with your finger, use a pencil or similar item.6. If the synchronization procedure is successful, a speed reading of 99.9 Km/h will appear in the display screen for one second. Your handlebarconsole will now receive data only from the resistance unit to which it has been linked. This link will remain even after a battery change.Troubleshooting:1. If the console display screen remains blank (no data appears while riding), or if data values are erratic, check the cable connection tothe computer console and consider replacing the batteries in the computer console and/or resistance unit.2. If the low battery indicator appears in the display screen, replace the batteries in the computer console and/or resistance unit.Changing Batteries:The computer console and resistance unit transmitter each use 2 “AA” batteries. When the low battery life indicator appears in the display,or if the display is erratic, faint or disappears altogether, new batteries are needed.ConsoleTo replace the console batteries, remove the battery cover from the underside of the computer console. Remove the used batteries anddispose of properly. Install fresh batteries according to the diagram inside the battery compartment, and replace the cover.TransmitterTo replace the transmitter batteries, remove the screws and open the cover on the underside of the resistance unit. See Figure 2. Removethe used batteries and dispose of properly. Install fresh batteries according to the diagram on the battery compartment cover, and replacethe cover.Note: During a battery change, current data and set-up values will be retained in memory.Bicycle Removal:1. While supporting the bicycle, open the lever handle (D) and lift the rear wheel up and forward to remove the rear axle from the axlesupport cups. See Figure 28.2. Note: The QR skewer provided with the trainer can be used when riding the bicycle off the trainer as well. If you choose to reinstallyour bicycle’s original skewer, refer to your bicycle owner’s manual for instructions on properly adjusting the skewer. Before riding,ensure the quick release skewer is tight.3. To fold the trainer for transport or storage, lower the upright frame legs carefully against the resistance unit (Figure 29), or fold the them360 degrees against the underside of the frame base tubes (Figure 30).Specifications:Battery Type:4 “AA” Alkaline CellsBattery Life:Approximately 300 hoursComputer Data Fields:Power (watts): up to 999 wattsSpeed: up to 99.9 miles/hour or 99.9 kilometers/hourDistance: up to 999.99 miles or kilometersOdometer: up to 99999 miles or kilometersRide Time: up to 9 hours, 99 minutes, 59 secondsTotal Time: up to 999 hours, 59 minutesElevation Gain: up to 9999 feet or metersWeight Input Field:up to 330 pounds or 150 kilogramsUnits of Measurement:Metric: Distance in Kilometers, Elevation in Meters, Weight in Kilograms, Speed in Kilometers/HourImperial: Distance in Miles, Elevation in Feet, Weight in Pounds, Speed in Miles/HourRide safely and enjoy your Nashbar Watt Master Fluid Wireless Trainer!5
Page 2: For Technical support, call 1-800-8

Click for Instruction Manual - Nashbar

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?