Model 1402 - Bulldog Security

More documents

Recommendations

Info

TESTING DOOR LOCKS CONT.CONNECTING DOOR LOCKS CONT.wires tests (+) positive when lock is pressed and the other tests (+)positive when they are unlocked, your vehicle has a “Type A” door“Type A” (+) Positive (5-pin harness)locking system. Make sure to mark which wire is lock and unlock. Proceedto Connecting Door Locks, Connecting Door Locks. NOTE: “Type A” andBLUE/BLACK Lock“Type C” locks will test the same, until you test for ground. Make sureyou run both tests before making your connections.BLUE/WHITE Not Used“Type B” Door Lock Test (Most Imports, some newer Fords)LOCKProbe both of your door lock wires going to the door lock switch usuallylocated in the driver’s kick panel. Attach the clip end of your test lightRED/BLACK+12V Constantto +12V. Using the vehicle’s door lock controls, activate the lock then theFUSEUNLOCKunlock testing both wires one at a time. If the test light illuminates whenyou probe the lock and the unlock wires your vehicle has a “Type B”GREEN/BLACK Unlockdoor locking system. Make sure to mark which wire is lock and unlock.Proceed to Connecting Door Locks.GREEN/WHITE Not Used“Type C” Door Lock Test (Most Fords, some Chryslers, GM Trucks)NOTE: Connect the RED WITH BLACK STRIPE wire to +12V constant power.(Optional part #778 required)Using your test light probe both the lock and the unlock wires usuallylocated in the driver’s kick panel. Attach the clip end of your test light“Type B” (-) Negative (5-pin harness)to ground probing both wires one at a time while locking and unlockingthe doors with the driver’s side switch (usually the master switch). TheBLUE/BLACK Locktest light should illuminate in both switch positions. Now attach the clipend of your test light to +12V constant, probe both wires one at a timeBLUE/WHITE Not Usedagain. The light should then illuminate again only in reverse order. Thistells you that you have a “Type C” reversing polarity system. Make sureLOCKto mark which wire is lock and unlock. Proceed to Connecting Door Locks.RED/BLACKGroundTesting Switch Wire and Motor Wires for” Type C” Door LocksFUSEBefore connecting, you must now determine which wire is the switch wireUNLOCKand which is the motor wire. Cut both the lock and unlock wires in half.GREEN/BLACK UnlockStart with both of the lock wires by placing the clip end of your test lightto ground, hold the door lock switch in the lock position, make sure youare using the master switch (usually on the driver’s door) and probe bothGREEN/WHITE Not Usedlock wires looking for voltage. The wire that illuminates the test light,NOTE: Connect the RED WITH BLACK STRIPE wire to ground.mark as the switch wire, the wire that shows no voltage, mark as themotor wire. Repeat the procedure for the unlock wire.One Wire Door Lock SystemSome vehicles have a single switch wire for both lock and unlock. Thissystem will wire as a “Type A” or “Type B” depending on the vehicle. Theonly difference being this system will require one or two resistors dependingon the make and model of the vehicle. Please consult our website for theproper resistor value for your vehicle. 1920MODULEMODULE‘
CONNECTING DOOR LOCKS CONT.“Type C” Reverse Polarity (5-pin harness)MODULEOne Wire Door Lock System (Example is for Chrysler)DOOR LOCK PLUGBLUE/BLACK LockBLUE/WHITE LockRED/BLACKBLUE/BLACK Lock OutputBLUE/WHITE Not UsedRED/BLACKFUSEGREEN/BLACK UnlockGREEN/WHITE UnlockFUSEGREEN/BLACK Unlock OutputGREEN/WHITE Not Used+12V ConstantNOTE: Connect the RED WITH BLACK STRIPEwire to +12V constant power.NOTE: You will need to cut factory wiring to make an endto end connection, see “Making Connections” on pages 2-4.620 OHM resistor tounlock, must be 5%tolerance.+12V Constant2700 OHM resistorto lock, must be 5%tolerance.NOTE: Connect the RED WITH BLACK STRIPEwire to +12V constant power.POWERDOORLOCKMOTORUNLOCKLOCKThis is a one (1)wire door lockingsystem and willrequire two (2)resistors to lockand unlock thedoors. Locate theWHITE/DKGREEN wire inthe driver’s kickpanel. This wirecontrols the doorlocks. Add theresistors asstated in thediagram. Wirethe unit in as a“Type A” system.21HOW TO USE YOURREMOTE TRANSMITTERBUTTON #1ARM/DISARMBUTTON #3OPTION #3*BULLDOGBUTTON #2OPTION #2BUTTON #4KEYLESS ENTRYFUNCTIONSLOCKING DOORSPress transmitter Button #1to lock the doors. Theparking lights will flash onceand the horn or siren willsound acknowledging theunit received the signal.UNLOCKING DOORSPressing transmitter Button #1 again will unlock the doors. The parking lightswill flash twice and then stay on for approximately 30 seconds and the hornor siren will sound twice acknowledging the unit received the signal. NOTE:If dome light feature is installed, the dome light will come on and stay on for30 seconds.LOCKING AND UNLOCKING WITH IGNITION SWITCHSee keyless entry programming options. NOTE: If your vehicle already hasthis option, (Factory Installed) do not activate.FULL TIME SILENT KEYLSS ENTRYThis will eliminate the horn or siren from sounding when locking or unlockingyour doors (See Silent Arming & Disarming in Alarm Programming Options).ARMINGPress Button #1 to arm the system. The siren will chirp once, the lights willflash once, the power door locks will lock and the LED will flash slowly toindicate that the system is now armed. The engine starter is also disabled.DISARMINGPress Button #1 while the system is armed and the system will be disarmed.The siren will chirp twice, the lights will flash twice (and stay on for 30 seconds)showing that the system is disarmed. If you hear three (3) siren chirps andsee three (3) light flashed when disarming, the vehicle was violated while youwere away. The LED will flash the zone violation (see page 23). When disarming,the dome light will turn on for 30 seconds.SILENT ARMING/DISARMINGPress and hold Button #1 to arm, but continue to hold the button. After three(3) seconds, the system will perform all arming functions as described above.except there will be no chirps (for this arming period only).22‘
Page 2 and 3: CONTENTSSystem Features ...........
Page 4 and 5: BEFORE YOU BEGIN CONT.technology an
Page 6: LOCATING & MAKINGCONNECTIONS CONT.3
Page 9: ‘ ‘LOCATING & MAKINGLOCATING &
Page 14: YOUR WARRANTYHere's how your warran

Model 1402 - Bulldog Security

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?