PDF - Pella.com

More documents

Recommendations

Info

6 INTERIOR SEAL:Caution: Ensure use of low pressure polyurethane window and door insulating foamsand strictly follow the foam manufacturer’s recommendations for application. Use ofhigh pressure foams or improper application of the foam may cause the door frame tobow and hinder operation.A. Add a sealant bead across the inner sill and 6" upeach jamb between the frame and rough opening.InteriorB. Apply insulating foam sealant. From the interior,between the door and the rough openingsurface of the shims to create a continuous seal.Follow foam manufacturer's instructions.Note: DO NOT place any foam between jambextensions and the rough opening.6"6C 6A6A 6BC. Check the door operation by opening andclosing the door.Note: If the door does not operate correctly,check to make sure it is still plumb, level, squareand that the sides are not bowed. If adjustmentsare required, remove the foam with a serratedknife. Adjust the shims, and reapply the insulatingfoam sealant.
7SEALINGTHE DOOR TO THEEXTERIOR WALL CLADDING:When applying siding, brick veneer or other exterior finish material, leave adequate spacebetween the door frame and the material for sealant. Refer to the illustration corresponding toyour finish material.Note: The sealant details shown are standard recommendations from the sealant industry.Contact your sealant supplier for recommendations and instructions for these and any otherapplications.InsulatingFoamBRICKVENEER3/8"Backer Rodand Sealanttypical3/8"ClearanceAccessoryGroovePerimeter Sealantmust extend toroom side ofAccessory Groove.InsulatingFoamVINYL/STEELSIDING3/8"Backer Rodand Sealanttypical3/8"ClearanceAccessoryGroovePerimeter Sealantmust extend toroom side ofAccessory Groove.InsulatingFoamSOUTHWESTERNWALLWITHSTUCCO3/8"Backer Rodand Sealanttypical3/8"ClearanceAccessoryGroovePerimeter Sealantmust extend toroom side ofAccessory Groove.3/8"Min.3/8"Min.3/8"Min.InsulatingFoamWOODSIDINGWITHTRIM3/8"Backer Rodand Sealanttypical3/8"ClearanceAccessoryGroovePerimeter Sealantmust extend toroom side ofAccessory Groove.InsulatingFoamSTUCCO3/8"Backer Rod andSealant typical3/8" ClearanceAccessoryGroovePerimeter Sealantmust extend toroomside ofAccessory Groove.3/8"Min.3/8"Min.Replacement Frame:Note: When applying siding, brick veneer or other exterior finish materials, leave adequatespace between the door frame and the material for sealant. Refer to the illustrationcorresponding to your finish material. Not allowing adequate space or not using backer rodmay cause the sealant to break down prematurely and allow water to infiltrate.InsulatingFoamBRICK VENEERBacker rodandsealant typicalInsulatingFoamWOOD SIDINGWITH TRIMBacker rodandsealant typical3/8"3/8"3/8"Min.
Page 1 and 2: © 2011 Pella CorporationPart Numbe
Page 3 and 4: 1 ROUGH OPENING PREPARATION (contin
Page 5 and 6: EXTERIOR SILL PAN LIP1 ROUGH OPENIN
Page 7 and 8: 3 SETTING AND FASTENING THE DOOR (c
Page 9 and 10: 3 SETTING AND FASTENING THE DOOR (c
Page 11 and 12: 5DOORREPLACEMENT IN SIDINGWITHOUT N
Page 13: 5DOOR REPLACEMENT IN SIDINGWITHOUT
Page 17: INTERIOR FINISHINGIf products canno

PDF - Pella.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?