PDF - Pella.com

More documents

Recommendations

Info

7SEALINGTHE DOOR TO THEEXTERIOR WALL CLADDING (continued)A. Insert backer rod into the space around theclearance between the backer rod and theNote: Backer rod adds shape and depth forthe sealant line.B. Apply a bead of high quality exterior gradesealant to the entire perimeter of the door.C. Shape, tool and clean excess sealant. Whenfinished, the sealant should be the shape ofan hourglass.7A7BD. Remove plastic guards at the base of thedoor once construction is complete.E. Install the hardware. Refer to the instructions
INTERIOR FINISHINGIf products cannot be finished immediately, cover with clear plastic to protect from dirt, damageand moisture. Remove any construction residue before finishing. Sand all wood surfaces lightlyPella products must be finished per the below instructions; failure to follow these instructions voidsthe Limited Warranty.FINISHING INSTRUCTIONSPaint or finish immediately after installation.Note: DO NOT paint, stain or finish weatherstrip or vinyl parts! If paint, stain or finish gets on theweatherstripping, wipe it off immediately with a damp cloth. To maintain proper performance, donot remove weatherstrip, foam corner seal wedges or gaskets. Air and water leakage may resultif these factory-installed items are removed. After finishing, allow doors to dry completely beforeclosing them. Pella will not be responsible for finishing imperfections. The use of unapprovedfinishes, solvents or cleaning chemicals may cause adverse reactions with door materials. Pella willnot be responsible for problems caused by the use fo unapproved materials. If in doubt, contactyour local retailer or representative.Use of inappropriate finishes, solvents, brickwash or cleaning chemicals will cause adverse actionswith window and door materials and voids the Limited Warranty.owner's manual by contacting your local Pella retailer. This information is also available on www.pella.com.Factory Prefinished Panels: A door panel that has been prefinished with stain or paint from thefactory requires no additional finishing. Clean the surface with mild soap and water. DO NOT useabrasives. DO NOT scrape or use tools that might damage the surface.Clad Exterior Frame:EnduraClad® baked-on-factory finish that needs no painting. Clean this surface with mild soap andwater. DO NOT use abrasives. DO NOT scrape or use tools that might damage the surface.Panel Cleaning and Prep Instructions for Unfinished or Primed Panels: Dry wipe dust fromconstruction. To remove smudges, lightly wipe surface with warm water. DO NOT sand surface ofsurface with mineral spirits for fiberglass panels and warm water for steel panels. Let door andsidelight surfaces dry completely before applying finish. Finish the door panels as soon as possibleafter installation.Staining fiberglass panels or unfinished interior frame members: Fiberglass door and sidelightpanels may be stained with a gel stain if a wood look is desired. Pella offers stain kits in a varietymay be stained with wood stains and should be finished with a minimum of two coats of a clearand the door panel.Note: The fiberglass base color tone will vary. This variance is normal and will not impact the staincolor of the door.Painting Instructions:that has a good blocking resistance. On units with glass, do not bridge paint between the outerFailure to use the correct type of finish may result in a door that sticks shut. Ask a qualified paintprofessional to specify a product with good blocking resistance.On patio doors:
Page 1 and 2: © 2011 Pella CorporationPart Numbe
Page 3 and 4: 1 ROUGH OPENING PREPARATION (contin
Page 5 and 6: EXTERIOR SILL PAN LIP1 ROUGH OPENIN
Page 7 and 8: 3 SETTING AND FASTENING THE DOOR (c
Page 9 and 10: 3 SETTING AND FASTENING THE DOOR (c
Page 11 and 12: 5DOORREPLACEMENT IN SIDINGWITHOUT N
Page 13 and 14: 5DOOR REPLACEMENT IN SIDINGWITHOUT
Page 15: 7SEALINGTHE DOOR TO THEEXTERIOR WAL

PDF - Pella.com

Create successful ePaper yourself

Delete template?

Save as template?