GTM Libra - Main build manual

More documents

Recommendations

Info

All other cables through the tunnel are tie wrapped to the p clipped cables. For rough locations in the tunnel refer to drawing No 8. Tie wraps can be found in fastener pack T0912. The Speedo cable T0702 is run down the RHS of the tunnel. Roughly make sure the Speedo cable can reach the instrument binnacle at the front of the car before tie wrapping it to the brake pipes. Run the clutch cable and wiring loom in a similar way. The handbrake cables will eventually also be tie wrapped to go over the petrol tank. The clutch cable, heater pipes and gear change rods run underneath the petrol tank. All other pipes through the tunnel will run over the petrol tank so it is important to get these cables close together so they will fit comfortably in the aperture. Before the petrol tank is put in place the rubber piping needs to be fitted to the rear end of the smaller aluminium heater pipes using Jubilee clips. These rubber pipes can then also be run over the petrol tank. Anything loose in this area will rub against the side of the gear change when used and eventually fail. When the car is complete ask someone to work the gear change whilst you have a good look under the tunnel to make sure that nothing is catching or fowling. © GTM CARS LTD. 6.9
LIGHTS FRONT END………………………………………………………….7.1 Main headlights assembly…………………………..7.1 Front indicators assembly………………………….7.1 Side repeater assembly……………………………...7.1 REAR END…………………………………………………………...7.3 Rear light unit assembly…………………………….7.3 Number plate light assembly……………………….7.3 Fog and reversing lamp assembly…………………7.3 © GTM CARS LTD. 6.10
Page 2 and 3: SECTION TITLE 1. Bonnet and Boot fi
Page 4 and 5: BEAM END COVERS Beam end covers are
Page 6 and 7: BOOT, BOOTLOCK AND HINGES The Libra
Page 8 and 9: Fit the boot rubber seal TO655 to t
Page 10 and 11: CARPETS The GTM Libra comes with a
Page 12 and 13: DASHBOARD TOP AND DEMISTER VENTS Th
Page 14 and 15: SEATS AND RUNNERS The Libra utilise
Page 16 and 17: SEPARATE INSTRUMENT OPTION In stand
Page 18 and 19: connectors. By wiring the fan switc
Page 20 and 21: half of the car. In the standard ki
Page 22 and 23: DOORS The Libra uses two glass fibr
Page 24 and 25: to enable the retaining clip to wor
Page 26 and 27: The arm that normally projects into
Page 28 and 29: ROOF PANEL A removable roof panel i
Page 30 and 31: ENGINE COVER MOULDING The engine co
Page 32 and 33: may be necessary to strain the fram
Page 34 and 35: FRONT AND REAR SUSPENSION FRONT SUS
Page 36 and 37: T0208 - FRONT BOTTOM SWIVEL. T0209
Page 38 and 39: Hold the completed bottom wishbone
Page 40 and 41: 2 x T0311 Rear suspension arm track
Page 42 and 43: Locate the two shock absorber brack
Page 44 and 45: Radiator mould, radiator & pipe wor
Page 46 and 47: attached to the heater unit using t
Page 48 and 49: The Ø6mm breather pipe is taken up
Page 50 and 51: assembly on the right hand side. A
Page 54 and 55: HEADLIGHT COVERS………………
Page 56 and 57: saw, opening up a hole just big eno
Page 58 and 59: FRONT & REAR SCREEN AND WIPERS SCRE
Page 60 and 61: and tinted and the rear screen is t
Page 62 and 63: ELECTRONICS & WIRING WIRING……
Page 64 and 65: Unfortunately the Rover 25 engine b
Page 66 and 67: the rear panel of the car to be rem
Page 68 and 69: through the wire to the handbrake w
Page 70 and 71: to the same bolt on the gearbox tha
Page 72 and 73: At the rear take the longest brake
Page 74 and 75: cables and handbrake lever are used
Page 76 and 77: PEDAL BOX AND MASTER CYLINDER The L
Page 78 and 79: throttle runs freely and make sure
Page 80 and 81: EXHAUST The exhaust system on the L
Page 82 and 83: SETTING UP THE CAR FOR THE ROAD The
Page 84 and 85: the car. Once you have set these bo
Page 86 and 87: Build Notes © GTM CARS LTD. 13.2
Page 88 and 89: Build Notes © GTM CARS LTD. 13.4
Page 90: Fitting Guide NEW SUSPENSION (Issue

GTM Libra - Main build manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?