GTM Libra - Main build manual

More documents

Recommendations

Info

Fit the boot rubber seal TO655 to the boot aperture finishing the seal at a position approximately 200mm either side of the position of the boot striker. The boot can now be finally adjusted and fitted by adjusting the hinge positions and the position of the boot striker in the boot lid. Spend some time getting it to work perfectly so that it will not catch when in operation. Grease the latch sparingly. SPARE WHEEL MOULD AND SPARE WHEEL The Libra utilises a full size spare wheel mounted in the front compartment of the Libra. The wheel is mounted in the engine ducting above the battery. The area inside the spare wheel is used to hold the jack tools for the Libra and forms the battery box lid. Spare Wheel mould and Spare Wheel assembly There are two 6mm studs captivated into the top of the battery mounting and these studs coincide with indentations marked on the spare wheel mould. Drill out these indentations with a Ø6mm clearance hole and place the spare wheel mould over the top of the battery mounting. The spare wheel mould holds the battery in place and gives you space for a few tools. It is held in place by two Ø6mm thumb screws. © GTM CARS LTD. 1.5
CARPETS AND INTERIOR FITTINGS CARPETS........................................................................2.2 Carpets assembly…………………………......2.2 DASHBOARD COVER………………………………………2.3 DASHBOARD TOP AND DEMISTER VENTS……………2.4 PART TRIM PANELS OPTION ASSEMBLY……………..2.4 SEATS AND RUNNERS…………………………………….2.6 Assembly........................................................2.6 SEAT BELTS…………………………………………………2.7 SEPARATE INSTRUMENT OPTION……………………...2.8 SOFT TRIM…………………………………………………..2.10 HARD TRIM PANELS (STANDARD KIT)………………..2.11 INSTRUMENT TRIM………………………………………...2.11 TRIMMING HARD PANELS………………………………..2.12 © GTM CARS LTD. 1.6
Page 2 and 3: SECTION TITLE 1. Bonnet and Boot fi
Page 4 and 5: BEAM END COVERS Beam end covers are
Page 6 and 7: BOOT, BOOTLOCK AND HINGES The Libra
Page 10 and 11: CARPETS The GTM Libra comes with a
Page 12 and 13: DASHBOARD TOP AND DEMISTER VENTS Th
Page 14 and 15: SEATS AND RUNNERS The Libra utilise
Page 16 and 17: SEPARATE INSTRUMENT OPTION In stand
Page 18 and 19: connectors. By wiring the fan switc
Page 20 and 21: half of the car. In the standard ki
Page 22 and 23: DOORS The Libra uses two glass fibr
Page 24 and 25: to enable the retaining clip to wor
Page 26 and 27: The arm that normally projects into
Page 28 and 29: ROOF PANEL A removable roof panel i
Page 30 and 31: ENGINE COVER MOULDING The engine co
Page 32 and 33: may be necessary to strain the fram
Page 34 and 35: FRONT AND REAR SUSPENSION FRONT SUS
Page 36 and 37: T0208 - FRONT BOTTOM SWIVEL. T0209
Page 38 and 39: Hold the completed bottom wishbone
Page 40 and 41: 2 x T0311 Rear suspension arm track
Page 42 and 43: Locate the two shock absorber brack
Page 44 and 45: Radiator mould, radiator & pipe wor
Page 46 and 47: attached to the heater unit using t
Page 48 and 49: The Ø6mm breather pipe is taken up
Page 50 and 51: assembly on the right hand side. A
Page 52 and 53: All other cables through the tunnel
Page 54 and 55: HEADLIGHT COVERS………………
Page 56 and 57: saw, opening up a hole just big eno
Page 58 and 59:
FRONT & REAR SCREEN AND WIPERS SCRE
Page 60 and 61:
and tinted and the rear screen is t
Page 62 and 63:
ELECTRONICS & WIRING WIRING……
Page 64 and 65:
Unfortunately the Rover 25 engine b
Page 66 and 67:
the rear panel of the car to be rem
Page 68 and 69:
through the wire to the handbrake w
Page 70 and 71:
to the same bolt on the gearbox tha
Page 72 and 73:
At the rear take the longest brake
Page 74 and 75:
cables and handbrake lever are used
Page 76 and 77:
PEDAL BOX AND MASTER CYLINDER The L
Page 78 and 79:
throttle runs freely and make sure
Page 80 and 81:
EXHAUST The exhaust system on the L
Page 82 and 83:
SETTING UP THE CAR FOR THE ROAD The
Page 84 and 85:
the car. Once you have set these bo
Page 86 and 87:
Build Notes © GTM CARS LTD. 13.2
Page 88 and 89:
Build Notes © GTM CARS LTD. 13.4
Page 90:
Fitting Guide NEW SUSPENSION (Issue
show all

GTM Libra - Main build manual

Create successful ePaper yourself

Delete template?

Save as template?