MI - Installer guide (5583 kb) - Elvox.com

More documents

Recommendations

Info

GBCONFIGURING THE VIDEO DOOR ENTRY UNITSelecting the type of ringtone.It is possible to select the types of ringtone to <strong>com</strong>bine with the different calls that the video door entry unitcan receive:- panel calls;- landing calls.Setting the entrance panel call ringtone.The ringtone for calls from the entrance panel is selected as follows:• With the MONITOR OFF, press button E or button F for at least 3 seconds to access the list of availabletones.• Using button E or button F, scroll through the list of tones, the video door entry unit will play the related ringtoneand save it in correspondence with the input of the entrance panel call (upon saving, the red LED willlight up for a few moments).Setting the landing call ringtone.To select the type of ringtone for landing calls, perform the following steps with the MONITOR OFF:• Simultaneously press and hold buttons E and F for approximately 3 seconds to access the list of availabletones; the red LED will start flashing.• Scroll through the list of tones using button E or button F; the video door entry unit will play the correspondingringtone and save it in correspondence with the input of the landing call and the red LED will go out.The red LED goes out after each programming phase or after a timeout of approximately 15 sec; if the LED goesout because of a timeout it is necessary to repeat the configuration.Ringtone volume adjustment.The volumes of the ringtones described above are adjusted in a similar manner for all types of call (from entrancepanel or landing panel). To adjustment is made as follows with the MONITOR OFF:• Press button H for at least 3 seconds to decrease the loudness of the ringtone;• Press button I for at least 3 seconds to increase the loudness of the ringtone.Speakerphone volume adjustment.With this procedure it is possible to adjust the volume of the audio channel that is transmitted from an speechunit to the speaker of the video door entry unit.The adjustment, to be made with the MONITOR ON and keeping button D pressed, is made as follows:• Press button H to decrease the loudness;• Press button I to increase the loudness.26/36
CONFIGURING THE VIDEO DOOR ENTRY UNITGBVideo parameter adjustment.The following procedure are used to set the three parameters that control the video picture on the LCD monitor:- brightness;- controls;- colour.Setting the brightness.To set the level of brightness of the LCD monitor, carry out the following operations with the MONITOR ON:• Press button E to decrease the brightness;• Press button F to increase the brightness.Setting the contrast.To set the level of contrast of the LCD monitor, carry out the following operations with the MONITOR ON:• Press button H to decrease the contrast;• Press button I to increase the contrast.Setting the colour.The colour adjustment is made with the trimmer located in the top left corner of monitor 68MV (see figure 20).Note: The colour setting is the least critical one and has the least effect on the quality of the picture on the LCDmonitor with respect to changes in ambient light.Setting the colourFigure 20 - Colour adjustment.27/36
Page 3 and 4: TECHNICAL SPECIFICATIONSGBThe devic
Page 5 and 6: TECHNICAL SPECIFICATIONSGBAdvantage
Page 7 and 8: TECHNICAL SPECIFICATIONSGBInput cur
Page 9 and 10: FUNCTIONS OF THE VIDEO DOOR ENTRY U
Page 21 and 22: INSTALLATION TOPOLOGYGBMONITOR CABL
Page 23 and 24: CONFIGURING THE VIDEO DOOR ENTRY UN
Page 25: CONFIGURING THE VIDEO DOOR ENTRY UN
Page 29 and 30: EXAMPLE OF PANEL TECHNICAL PARAMETE
Page 31 and 32: INTEGRATION OF THE VIDEO DOOR ENTRY
Page 33 and 34: REGOLE E CONFORMITÀGBInstallation
Page 35 and 36: SAFETY INSTRUCTIONS FOR INSTALLERSG

MI - Installer guide (5583 kb) - Elvox.com

Create successful ePaper yourself

Delete template?

Save as template?