864 ST Fireplace Installation Manual - Lopi

More documents

Recommendations

Info

28 Finalizing the Installation (for qualified installers only)Termination Requirements! Venting terminals shall not be recessed into a wall or siding.ABCDEFGHIJKLMNMinimum 9" clearance from any door or windowMinimum 12" above any grade, veranda, porch, deck or balconyMinimum 3-3/8" from outside corner wallsNOTE: Clearance in accordance with local installation codes and the requirementsof the gas supplier.Minimum 12" from inside corner wallsNOTE: Clearance in accordance with local installation codes and the requirementsof the gas supplier.RoofSurface11” Min.6” Min.RoofEavesMinimum 11" clearance below unventilated soffits or roof surfacesMinimum 18" clearance below ventilated soffitsMinimum 6" clearance below roof eavesNOTE: Vinyl surfaces require 24"NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.Minimum 12" clearance below a veranda, porch, deck or balconyNOTE: Permitted only if veranda, porch, deck, or balcony is fully open on a minumum of two sides beneath the floor.NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.Minimum 48" clearance from any adjacent buildingMinimum 84" clearance above any grade when adjacent to public walkways or drivewaysNOTE: may not be used over a walkway or driveway shared by an adjacent buildingMinimum 9" clearance to any nonmechanical air supply inlet to the building or the combustion air inlet to any otherappliance.Minimum 36" clearance above any mechanical air supply inlet if within 10’ horizontallyMinimum 36" from the area above the meter/regulator (vent outlet)NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.Minimum 36" from the meter/regulator (vent outlet)NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.Minimum 12” above the roof line (for vertical terminations)Minimum 24” horizontal clearance to any surface (such as an exterior wall) – for vertical terminationsENMEKEAJGFDALCIHBNOTE: Measure clearances to the nearest edge of the exhaust hood.• Use the vinyl siding standoff when installing on an exterior with vinyl siding.• Vent termination must not be located where it will become plugged by snow or other materialTravis Industries 4071126 100-01195_000
Finalizing the Installation (for qualified installers only) 29Hearth RequirementsFloor Mounted for the access door).FireplacesWARNING:Do not build a hearth morethan 1” above the baseplate(this area must remain clearIf installed near carpet or othercombustible flooring, the fireplacemust be raised so the base of theunit is above the carpet surface orflooring material.A non-combustible hearth is not required. However, ifthe heater is installed next to the floor, we recommenda hearth to protect the flooring surface fromdiscoloration or other negative impact from the heater.Raised Fireplacessurface.Fireplace StandA hearth is not requiredwhen the fireplace israised above the flooring© Travis Industries 4071126 100-01195_000
Page 1 and 2: 864 STFireplaceInstallationManualTe
Page 3 and 4: Table of Contents 3IntroductionOver
Page 5 and 6: Safety Warnings (continued):Safety
Page 7 and 8: Packing ListFinalizing the Installa
Page 9 and 10: Finalizing the Installation (for qu
Page 19 and 20: Approved VentFinalizing the Install
Page 27: Finalizing the Installation (for qu
Page 31 and 32: Facing OverviewFinalizing the Insta
Page 47 and 48: Back Left LogFinalizing the Install
Page 49 and 50: Back Left LogFinalizing the Install
Page 53 and 54: Optional Equipment (for qualified i
Page 61 and 62: Andiron InstallationOptional Equipm

864 ST Fireplace Installation Manual - Lopi

Create successful ePaper yourself

Delete template?

Save as template?