Drive technology for AC and DC

More documents

Recommendations

Info

VDC-3-49-15with electronics module K5– Completely integrated operation and control electronics “K5” with CANopen communication interfaceand programming functionality– Sine commutation of the drive based on field oriented control (FOC) and 4-quadrant operation– Speed control range down to n=0 rpm with holding torque– Different modes of operation based on DSP 402 standard (speed, position, homing, torque) throughCANopen interface– Electronics-module in IP 54 version– Connector system in sealed M12 industry standard– Interface with digital inputsNominal dataTypeVDC5-3-49.15 B00Nominal voltage (U N ) V DC 24Permissible supply voltage range (U ZK ) V DC 18 to 30Nominal speed (n N ) rpm 4 000Nominal torque (M N ) mNm 150Nominal current (I N ) A 3,5Nominal output power (P N ) W 63Speed at no-load operation (n L ) rpm 4 000No-load current (I L ) A 0,4Max. reverse voltage V DC 36,7Set value inputCan BusSet speed rpm 0 … 4 000Recommended speed control range rpm 0 … 4 000Locked-rotor protectionthermalwith locked-rotor protection clocknoOverload protectionyesStarting torque mNm 300Rotor moment of inertia (J R ) kgm 2 x10 –6 108Thermal resistance (R th ) K/W –Protection class IP 54*Ambient temperature range (T U ) °C 0 … +40Motor mass (m) kg 0,59Order No. -* Type of protection specified pertains to installed state with seal on the flange side.F radialL 160F axialF axial 20 NF radial 60 N L 1 10 mmPermissible shaft load at nominal speed and lifeexpectancy L 10 at 20 000 h (at T U max. 40°C).15 18 1870,550[min -1 ][x1000]4M[A]103833327,55,0Ø 25 h7Ø 6 g586,54,55 H104x36 +_ 0,240 +_ 0,249 +_ 0,24x 90°1I2,502 +_ 0,120 +0,361+0,545°4x 90°15°3,65 H108x120 180 240 300[mNm]Ø 63 +_ 0,236
Description of connection interface with electronics module K5The VDC-3-49.15 with built-on electronics module K5 is an extremelycompact drive unit.With the CANopen interface, the extensive functionality and the robustdesign the motor is suitable for a large variety of applications such asautomated format adjustments or torque-controlled winder drives.Power:CAN-IN:CAN-OUT:Power CAN-IN CAN-OUT3345˚12245˚45454145˚213Pin 1 UZK Power supply motorPin 2 GND Power/ logic supplyPin 3 UB Logic supplyPin 4 IN 1 Digital inputPin 1 n.c.Pin 2 IN 2 Digital inputPin 3 CAN-GND CAN-GNDPin 4 CAN_H CAN High SignalPin 5 CAN_L CAN Low SignalPin 1 n.c.Pin 2 IN 3 Digital inputPin 3 CAN-GND CAN-GNDPin 4 CAN_H CAN High SignalPin 5 CAN_L CAN Low Signal37Representatives Specifications AC motorsBCI motorBG motorECI motorVarioDrive C VARIODRIVE Compact VARIODRIVE Information
Page 1: Drive technologyfor AC and DCversio
Page 4 and 5: Company profile: ebm-papstThe entir
Page 6 and 7: Sustainability is at the centre of
Page 8 and 9: Motor technologyElectronic motor co
Page 10 and 11: Motor technologyThe internal rotor
Page 12 and 13: Motor technologyThe KM capacitor mo
Page 14 and 15: VARIODRIVETechnical informationVARI
Page 17 and 18: VARIODRIVE motorVD-3-43.10Informati
Page 20 and 21: DRIVECONTROLVT-A seriesOperating el
Page 22 and 23: AccessoriesElectrical connectionEle
Page 24 and 25: VARIODRIVE motorsThe following diag
Page 26 and 27: VARIODRIVE CompactTechnical informa
Page 28 and 29: VARIODRIVE Compact motorVDC-3-43.10
Page 38 and 39: VARIODRIVE Compact gearmotorVDC-3-4
Page 42 and 43: 50,613,5±0,270VARIODRIVE Compact g
Page 55 and 56: VarioDrive CVarioDrive C, technical
Page 57 and 58: Application areas:The VarioDrive C
Page 59 and 60: EC drive motorsVarioDrive C, size 0
Page 61 and 62: Nominal dataTypeM3G084-GF06 -42subj
Page 63 and 64: Nominal dataTypeM3G112-IA85 -71subj
Page 65 and 66: Nominal dataTypeM3G112-GA53 -72subj
Page 67 and 68: Nominal dataTypeM3G150-FF21 -51subj
Page 69 and 70: Nominal dataTypeM3G150-NA02 -52subj
Page 71 and 72: L7)Electrical connection VarioDrive
Page 73: L5)Electrical connection VarioDrive
Page 76 and 77: The ECI motor - dynamics, performan
Page 78 and 79: ECI motorsThe following diagram ill
Page 80 and 81: ECI motorECI-C-42.40- Dynamic 3-pha
Page 82 and 83: YECI gearmotorECI-C-42.40-PX- Dynam
Page 84 and 85: 60°ECI motorECI 63.40- Highly dyna
Page 86 and 87:
ECI 63.20with electronics module K5
Page 88 and 89:
ECI 63.60with electronics module K5
Page 90 and 91:
ECI gearbox versionsECI with Perfor
Page 92 and 93:
ECI gearbox versionsECI with Noisel
Page 94 and 95:
ECI sensor module externalEncoder H
Page 96 and 97:
ECI brake module externalSpring app
Page 98 and 99:
ECI 63 with electronics K5Commissio
Page 100 and 101:
ECI 63 with electronics K5Commissio
Page 102 and 103:
102
Page 104 and 105:
BG 43 motorTechnical informationThe
Page 106 and 107:
BG 43 motorBG 4310- 3-core internal
Page 108 and 109:
BG 43 motorBG 4340- 3-core internal
Page 110 and 111:
110
Page 112 and 113:
BCI motor - the complete drive solu
Page 114 and 115:
BCI motorBCI 42.25- Direct current
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
BCI motorBCI 42.25 A spur gearmotor
Page 122 and 123:
BCI motorBCI 42 PX planetary gearbo
Page 124 and 125:
BCI motorBCI 52.60 PX planetary gea
Page 126 and 127:
BCI motorBCI 63 B spur gearmotor24
Page 128 and 129:
BCI motorBCI 63 E spur gearmotor24
Page 130 and 131:
BCI motorBCI 63 SB worm gearmotor24
Page 132 and 133:
BCI brake24 V DC- The spring-applie
Page 134 and 135:
BCI sensorEncoder HEDS 5500- Optoel
Page 136 and 137:
AC motorsTechnical informationEM Sh
Page 138 and 139:
Shaded-pole motorsEM 25Standard ver
Page 140 and 141:
Capacitor motorsKM 40 IP00Standard
Page 142 and 143:
Capacitor motorsKM 43 IP20Standard
Page 144 and 145:
Gear motorsGtg 78- Shaded-pole moto
Page 146 and 147:
146
Page 148 and 149:
Basic information on standards and
Page 150 and 151:
Basic information on standards and
Page 152 and 153:
Definitions for EC motorsAll inform
Page 154 and 155:
Definitions for EC motorsProtection
Page 156 and 157:
Definitions for DC motorsNominal vo
Page 158 and 159:
fan agentcompact fan agentebm-papst
Page 160 and 161:
Page 162 and 163:
Page 164:
37633-7-8811 · RA-06/11-4’M1138
show all

Drive technology for AC and DC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?