The driving force

Recommendations

Info

106 GROTEFELD DN-SPL GROTEFELD DN-SPL 107 ø129 60 Milling receptacle ø30h6 x 60 ø30 h6 ø65 Collet receptacle Hi-Q/ER40 torsion 2x (cylinder pin 6m6x16 DIN6325) SW41 (Open end spanner SW41) Technical features Item Id EP-120641 drive turning direction R.H./(L.H.) drive speed max. permanent operation = 18.000 rpm spindle position vertical tool receptacle Ø30 x 60 mm with 3x M6 mounting thread - special equipment on request gear ratio 1 : 1 turning direction of tool receptacle equal to drive turning direction spindle speed max. permanent operation = 18.000 rpm drive adapter according to customer’s request max. drive capacity 3,0 kW weight 3,05 kg with HSK-F63 (as per illustration) 206 Drive adapter Standard configurations and machine specific executions upon request clamping depth 46 ø2-ø30mm ø63 Counternut CM/ER40 (Hook wrench 58/62) Screwcap Hi-Q/ER40 (Key for Collet E40) Collet ER40 DIN6499-B (option) The Direct receptacle DN-SPL is always supplied with a drive spindle according to your indications. It is necessary to indicate - in case of order - the information regarding the drive spindle in question in addition to the article-number. Usually it is a spindle according to the DIN / ISO regulations. Corresponding to your order you will receive within our order confirmation a final article-number that was extended by the information referring to the direct receptacle built for you. This article-number then applies for this specific configuration and can be used for all further orders without any additional information. 52 60 137 Description of the function The chip guiding systems of the series DN-SPL have a tool receptacle according to your specifications. The direct receptacle DN-SPL is used for direct reception of tools for the processing of solid wood or wood-like composite materials. The standing adapter casing (due to torque support) is used for mounting chip deflectors, according to the used profiling tool. The maximum spindle speed is 18.000 rpm in permanent operation. Attention: We advise tools of aluminum body ø30 h6 ø65 In the selection and purchase of tools, you should prefer cutters with an aluminum body to minimize the rotating forces. Additionally the fine counter balance of the tools must be considered. Variants on demand!
108 109 Tracing spindles Direct-drive spindles
Page 1 and 2:
120 1 The driving force. GROTEFELD
Page 3 and 4: 4 Survey Survey 5 W01 angular sawin
Page 5 and 6: 8 Survey Survey 9 G30 angular heads
Page 7 and 8: 12 13 Sawing units Drilling units M
Page 9 and 10: Drive adapter Standard configuratio
Page 11 and 12: 20 GROTEFELD G03-4.4-P GROTEFELD G0
Page 13 and 14: 24 GROTEFELD G03-4.4-2B2P GROTEFELD
Page 15 and 16: 28 Receptacle Views for G03 Recepta
Page 17 and 18: 32 GROTEFELD G06-1.1-F GROTEFELD G0
Page 21 and 22: 40 Receptacle Views for G06 Recepta
Page 23 and 24: 7 44 Drive adapter GROTEFELD G07-1.
Page 27 and 28: 52 GROTEFELD W09-4.3-B GROTEFELD W0
Page 29 and 30: Drive adapter 56 GROTEFELD G10-4.5-
Page 31 and 32: 60 GROTEFELD W12 GROTEFELD W12 61 t
Page 33 and 34: 64 GROTEFELD G16-1.1-P Drive adapte
Page 35 and 36: 68 GROTEFELD W17-1.1-P GROTEFELD W1
Page 37 and 38: 72 GROTEFELD W19-1.2-B GROTEFELD W1
Page 41 and 42: 80 GROTEFELD G30 GROTEFELD G30 81 1
Page 43 and 44: 84 GROTEFELD G200-3.3-B GROTEFELD G
Page 45 and 46: 88 GROTEFELD G200-1.1-P16 GROTEFELD
Page 47 and 48: ntour ø116mm 70 39 92 GROTEFELD UN
Page 49 and 50: clam 96 Receptacle Views for UNI1-S
Page 51 and 52: 100 Receptacle Views for DPL Recept
Page 53: 104 GROTEFELD DN-VCM GROTEFELD DN-V
Page 57 and 58: 112 GROTEFELD FN6-1.1-B GROTEFELD F
Page 59 and 60: 116 GROTEFELD FN7-1.1-S GROTEFELD F
Page 61 and 62: 7 5 3 1 8 6 4 2 0 120 GROTEFELD FN7
Page 63 and 64: 124 GROTEFELD FN9-1.3-SF GROTEFELD
Page 65 and 66: 128 GROTEFELD FN12-1.1-P30 GROTEFEL
Page 67 and 68: 4 132 GROTEFELD FU7-1.1-S GROTEFELD
Page 69 and 70: 136 Optional accessories Optional a
show all

The driving force

Create successful ePaper yourself

Delete template?

Save as template?