Protection Design Guide for Portable Electronics - Semtech
Protection Design Guide for Portable Electronics - Semtech
Protection Design Guide for Portable Electronics - Semtech
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
PROTECTION PRODUCTS<br />
MDDI Interface - Low Profile, Low Capacitance<br />
RClamp ® 0522T and RClamp ® 0524T<br />
The RClamp0522T and RClamp0524T are ultra-low<br />
capacitance ESD protection devices that have been<br />
optimized <strong>for</strong> use on next generation serial display interfaces.<br />
Each have a typical capacitance of only 0.30pF<br />
between I/O pins and 0.80pF between any I/O pin and<br />
ground. This allows it to be used on circuits operating<br />
in excess of 3GHz without signal attenuation. They<br />
may be used to meet the ESD immunity requirements<br />
of IEC 61000-4-2, Level 4 (±15kV air, ±8kV contact<br />
discharge). The RClamp0522T is designed to protect<br />
two lines, while the RClamp0524T will protect four lines.<br />
The RClamp0522T is in a 6-pin, RoHS/WEEE compliant,<br />
SLP1610P4T package. It measures 1.6 x 1.0 x 0.40mm.<br />
The RClamp0524T is in a 10-pin, RoHS/WEEE compliant,<br />
SLP2510P8T package. It measures 2.5 x 1.0 x 0.40mm.<br />
The leads are spaced at a pitch of 0.5mm. They are<br />
designed <strong>for</strong> easy PCB layout by allowing the traces to run<br />
straight through the device. The leadless design and flow<br />
through layout minimizes impedance stubs <strong>for</strong> maximum<br />
signal integrity.<br />
For a complete solution, the power lines should also be<br />
protected. Here a “general purpose” single line device<br />
such as uClamp0501P will suffice.<br />
© 2009 <strong>Semtech</strong> Corp.<br />
10<br />
SI08-01<br />
<strong>Protection</strong> <strong>Design</strong> <strong>Guide</strong><br />
<strong>for</strong> <strong>Portable</strong> <strong>Electronics</strong><br />
LCD Display - Serial & Parallel Interface<br />
Low Capacitance MDDI/MIPI Port protection<br />
MDDI Link<br />
Controller<br />
MDDI_Data0+<br />
MDDI_Data0-<br />
Gnd Gnd<br />
MDDI_Data1+<br />
MDDI_Data1-<br />
RClamp0524T RClamp0524T<br />
MDDI_Stb+<br />
MDDI_Stb-<br />
Gnd Gnd<br />
RClamp0522T RClamp0522T<br />
Host Pwr<br />
RClamp0522T (1.6 x 1.0 x 0.40mm)<br />
RClamp0524T (2.5 x 1.0 x 0.40mm)<br />
MDDI Link<br />
Controller<br />
Host Gnd<br />
HOST<br />
uClamp0501P<br />
uClamp0501P<br />
DISPLAY<br />
Pin 1 Pin 2<br />
3, 4<br />
1 2<br />
Pin 1 Pin 2 Pin 4 Pin 5<br />
10<br />
3, 8<br />
9<br />
8 7 6<br />
1 2 4 5<br />
3<br />
6 5 4<br />
3<br />
www.semtech.com