Jenkins Fan Catalog

SerieS 5 - armaTUre/roTor
Series 5 fans are suitable for internal cooling of an AC motor. They have a hub,
which protrudes from the back plate on the opposite side of the blades. This
protruding hub can fit under the rotor end turns or end ring without interfering
with the bearing housings. Photo 501 fans have openings in the back plate to
allow air movement through the fan. This allows the fan to draw air through
the rotor and then push it toward the stator end turns or out the end bells of
the motor. Photo 502 fans have a solid back plate. Air cannot be moved along
the shaft through this type of fan.
Line
#
N
E
W
Overall
Diam
(D)
Our Fan
Catalog
Number
List
Price
$
Refer to
Photo #
Blades,
Material,
Wt (ibs)
Width
of
Blades
(A)
Hub
Diam
(B)
Hub
Thickness
(C)
Hub
Recess
(E)
Plate
Diam
(H)
Maximum
Allowed
Bore
Typical
Frame
Number
1 1-7/8 5-5672 $66.00 79 7-Al-1 3/8 5/8 5/8 -1/4 1-7/8 3/8
2 2 5-4724 66.00 --- 6-Al-1 7/16 1/2 5/8 -1/2 2 1/8
3 4-1/2 5-383 66.00 510 8-Al-1 5/8 2-7/8 3/4 -5/8 4-1/2 2-3/8
4 4-1/2 5-5754 66.00 672 4-Al-1 1-1/8 7/8 1/2 3/4 1 1/2
5 4-5/8 5-5828 66.00 502 12-Al-1 7/16 1-1/8 2 -3/8 4-7/8 5/8
6 4-7/8 5-8040 66.00 672 8-Al-1 1-3/8 1 1/2 7/8 3-1/8 1/2
7 • 4-7/8 5-6566 66.00 --- 12-Al-1 7/16 1-1/8 2 -3/8 4-7/8 5/8
8 5 5-166 522.00 630 10-Al-8 1-1/8 1-1/4 1 -1/8 4-3/4 3/4
9 5 5-5696 66.00 501 9-Al-1 1 1-1/2 1/2 -3/8 5 1
10 5 5-7175 66.00 502 12-Al-1 7/8 1-3/4 5/8 5/8 5 1-1/4
11 5-1/8 5-4636 66.00 61 10-Al-1 1-3/8 2 1 1/2 3-5/8 1-1/2
12 5-1/4 5-1955 66.00 525 15-Al-1 1 1-1/2 1/2 3/8 5-1/4 1
13 5-1/4 5-8651 66.00 502 9-Al-1 1-1/2 2-3/8 1 -3/8 5-1/4 1-7/8 162
14 5-3/8 5-30 66.00 155 15-Al-1 5/8 1-3/4 1 -1/4 5-3/8 1
15 5-3/8 5-4936 131.00 --- 12-Al-2 3/4 1-5/8 5/8 -3/8 5-3/8 1-1/8
16 5-1/2 5-4278 131.00 510 6-Al-2 2-3/16 2-3/16 3/4 -3/4 5-1/2 1-5/8
17 5-1/2 5-8323 66.00 510 12-Al-1 1-1/4 1-1/2 1-3/8 5/8 5 1
18 5-3/4 5-4653 131.00 81 9-Al-2 2-1/8 2-1/2 1-1/2 -1-1/8 5-3/8 2
19 5-3/4 5-4987 66.00 --- 6-Al-1 2 1-5/8 5/8 1-3/8 0 1-1/8
20 5-7/8 5-4287 66.00 510 12-Al-1 1/2 2 1-1/4 3/4 4 1-1/2
21 5-7/8 5-4889 131.00 --- 8-Al-2 1-1/8 1-15/16 0 -3/4 0 1-7/16
22 6 5-5200 66.00 1055 8-Al-1 2-1/4 2 1/2 3/4 4-1/4 1-1/2
23 6-1/8 5-1180 131.00 510 16-Al-2 1-7/8 2-5/8 3/4 1-3/4 6-1/8 2-1/8
24 6-1/4 5-1 66.00 510 12-Al-1 1-1/4 2-3/8 3/4 1 5-3/4 1-7/8
25 6-1/2 5-4817 66.00 --- 9-Al-1 2-1/2 2-3/8 1/2 1-3/8 6-1/2 1-7/8
26 6-1/2 5-4901 66.00 --- 12-Al-1 5/8 1-3/4 3/4 1-1/8 0 1-1/4
27 • 6-1/2 5-5051 196.00 --- 8-Al-3 1-1/8 2-5/8 5-1/8 -1 6-1/2 2
28 6-5/8 5-2133 131.00 626 9-Al-2 2-1/2 2 2-1/8 -1/8 5-5/8 1-1/2 Saw
29 6-5/8 5-4689 66.00 --- 15-Al-1 1 2-1/8 3/8 1-1/8 5-1/4 1-5/8
30 6-3/4 5-1785 66.00 1065 12-Al-1 3/4 2 3/4 1-3/8 4-1/4 1-1/2
31 6-3/4 5-4456 66.00 550 16-Al-1 1-1/4 2 1 7/8 4-3/4 1-1/2 184C
32 • 6-7/8 5-4746 131.00 --- 5-Al-2 2-3/8 3-1/2 2-1/2 -3/4 6-7/8 3
33 7 5-3048 131.00 555 10-Al-2 1-1/2 4-1/2 1-1/4 1-3/4 7 4
34 7 5-4276 131.00 510 16-Al-2 2-1/2 3 1 2 7 2-1/2 286UC
35 7-1/8 5-6042 131.00 510 10-Al-2 1-7/8 2-1/8 4 3-1/2 4 1-3/4
36 7-1/4 5-2 131.00 901 9-Al-2 1-3/4 2 3/4 1-1/4 7-1/4 1-1/2
37 7-1/4 5-4655 196.00 510 9-Al-3 5/8 2-1/4 2-1/4 1-3/4 7-1/4 1-3/4
38 7-1/4 5-4935 131.00 --- 12-Al-2 3/4 2-3/8 1/4 -1/4 8 1-7/8
39 7-1/4 5-5002 131.00 555 24-Al-2 1-3/4 3 1/2 2-5/16 7-1/4 2-1/2
40 7-1/4 5-5916 66.00 1055 18-Al-1 1 1-7/8 1-1/8 3/8 5-5/8 1-1/4
41 7-3/8 5-3 66.00 510 12-Al-1 1 2 7/8 3/4 4-1/2 1-1/2
42 7-3/8 5-7710 66.00 502 11-Al-1 1-5/8 1-5/8 1-3/8 5/8 5-3/8 1-1/8
43 7-1/2 5-3775 66.00 501 9-Al-1 5/8 2-1/2 1/2 1/4 2-1/2 2
44 7-5/8 5-2701 66.00 510 24-Al-1 5/8 1-3/8 5/8 3/8 7-5/8 1-1/8
45 7-3/4 5-5042 261.00 --- 7-Al-4 2-1/2 3-3/8 1-1/4 0 7-3/4 2-7/8
46 7-7/8 5-497 196.00 515 16-Al-3 1-3/4 2-3/4 2 1/2 5-1/4 2-1/4
47 7-7/8 5-6951 196.00 550 8-Al-3 1-1/4 2-3/4 2-1/8 7/8 5-1/2 2-1/4
48 8 5-3041 131.00 510 12-Al-2 1-1/8 2-1/4 7/8 7/8 8 1-3/4
49 8 5-6040 131.00 555 11-Al-2 1-5/8 3-5/8 1-1/4 2-1/2 7 3-1/8 365
50 8-1/8 5-2325 131.00 701 11-Al-2 1-5/8 1-3/4 1-5/8 3/8 7-7/8 1-1/4
36
See Table B2 on page 5 for blank fan machining charges.
For more photos please visit our website at www.jenkins.com