Jenkins Fan Catalog

SerieS 5 - armaTUre/roTor
Line
#
N
E
W
Overall
Diam
(D)
Our Fan
Catalog
Number
List
Price
$
Refer to
Photo #
Blades,
Material,
Wt (ibs)
Width
of
Blades
(A)
110 15 5-6037 $522.00 37 12-Al-8 2 3-3/4 2 1-3/8 12-1/2 2-7/8 426C
111 15 5-8392 652.00 501 14-Al-10 3 3-1/2 2 1-1/8 15 3
112 15 5-8652 783.00 501 12-Al-12 2-1/4 4-1/2 1-7/8 -1-3/4 13-3/4 3-3/4
113 15-1/4 5-6820 457.00 535 19-Al-7 1 4 1-1/2 1-1/2 13 3-1/4 DC
114 15-1/2 5-9498 196.00 --- 12-Al-3 1-1/4 2-1/4 1-3/4 1 13 1-3/4
115 • 15-3/4 5-6439 261.00 --- 8-Al-4 3-1/2 3-3/8 3/4 3-7/8 12-1/2 2-7/8
116 15-7/8 5-9 522.00 501 12-Al-8 2 4-1/2 1-1/4 1-3/4 14 3-3/4
117 16-1/8 5-167 652.00 155 15-Al-10 2-3/4 4-5/8 1-7/8 -7/8 16 3-7/8
118 16-1/4 5-8615 848.00 1045 12-Al-13 3-1/2 6 2-1/2 7/8 11-3/8 5-1/4 Special
119 16-3/4 5-4273 848.00 555 12-Al-13 3 6-1/4 2-1/2 2-1/2 17 5-1/2 OH
120 16-3/4 5-6844 913.00 210 15-Al-14 3-7/8 3-1/4 2-1/4 3/4 6-1/2 2-1/2
121 17 5-6846 392.00 155 12-Al-6 1-1/2 5 1-1/2 2 14-1/2 4
122 17-3/4 5-3414 652.00 540 24-Al-10 1-7/8 6-1/4 1-1/2 0 15 5-1/2
123 • 17-7/8 5-4664 652.00 --- 27-Al-10 1-5/8 6 1-1/2 6 17-7/8 5-1/2
124 • 18 5-6570 1174.00 --- 15-Al-18 5-1/4 6-3/4 2-5/8 -1/2 18 6-1/4
125 18-3/8 5-14 1370.00 255 12-Al-21 2-1/4 7 3-1/2 1-3/8 9-3/4 6-1/4
126 • 18-3/8 5-8943 522.00 --- 12-Al-8 2-5/16 8-1/4 3/8 0 12 6-3/4
127 18-7/8 5-5092 1370.00 --- 18-Al-21 3-1/2 8-1/2 2-1/16 1-3/4 0 8
128 19-1/4 5-6821 1174.00 660 9-Al-18 6-5/8 5-3/4 2 3-7/8 16-5/8 5
129 24-1/8 5-555 848.00 545 8-Al-13 2-3/4 7 1-5/8 1-1/4 18-1/2 6-1/4 C6085
130 24-5/8 5-5047 2087.00 --- 19-Al-32 6-3/16 5-1/2 2 4 17-3/4 5
131 29-5/8 5-5208 3195.00 155 16-Al-49 3-1/2 14 2-3/8 1-1/8 29-5/8 13-1/5 8511SU
132 34 5-4983 2478.00 --- 8-Al-38 3-1/2 14-1/4 2-1/2 0 0 13-1/2
133 35-1/2 5-9484 5868.00 --- 19-Al-90 8-1/2 10 3-3/4 -1/2 30 9
Hub
Diam
(B)
Hub
Thickness
(C)
Hub
Recess
(E)
Plate
Diam
(H)
Maximum
Allowed
Bore
Typical
Frame
Number
SerieS 6 - Deep reCeSS
Series 6 fans are those with deep dished back plate, i.e., dimension “E” is
relatively large. This type is used on many European motors and some old
American designs. To change European frame sizes (IEC Numbers) to the
approximate NEMA frame, multiply the IEC number by (1.6). The IEC frame
number is the motor shaft height (D) in milimeters. The deep hub recess
allows the fan to fit around a protruding bearing housing. Some of the Series
1 fans also have a sizeable hub recess, so the distinction between them and
the Series 6 is not rigorous.
Line
#
N
E
W
Overall
Diam
(D)
Our Fan
Catalog
Number
List
Price
$
Refer to
Photo #
Blades,
Material,
Wt (ibs)
Width
of
Blades
(A)
Hub
Diam
(B)
Hub
Thickness
(C)
Hub
Recess
(E)
Plate
Diam
(H)
Maximum
Allowed
Bore
1 2-5/8 6-84 $66.00 616 12-Al-1 1/2 1 1/2 1/4 2-5/8 1/2
2 3-1/4 6-8321 66.00 601 8-Al-1 3/4 1-1/4 5/8 1-1/8 3-1/8 3/4
3 3-3/4 6-3695 66.00 601 10-Al-1 7/8 7/8 1/2 1/8 3-1/8 3/8
4 3-7/8 6-34 66.00 642 12-Al-1 1 7/8 3/4 1/4 3 3/8 56
5 3-7/8 6-7771 66.00 626 7-Al-1 5/8 1 3/4 1/8 3 1/2
6 4 6-6123 66.00 151 11-Al-1 5/8 1-1/2 1/2 1/8 3 1
7 4-5/8 6-27 66.00 642 12-Al-1 7/8 1-1/4 3/8 1/2 3-1/2 3/4 63
8 4-5/8 6-3970 66.00 642 12-Al-1 1-1/2 1-1/4 1/2 1/2 3-1/2 3/4
9 4-7/8 6-31 66.00 622 10-Al-1 1-1/8 1 3/4 1/4 3-3/4 1/2 71
10 5 6-35 66.00 642 10-Al-1 1-1/4 1-1/8 3/4 3/8 3-5/8 5/8 80
11 5 6-36 66.00 642 12-Al-1 7/8 1-3/4 5/8 3/8 4-1/4 1-1/4 80
12 5 6-5091 66.00 --- 12-Al-1 1-1/8 1-1/2 1/2 3/8 3-1/8 1
13 5-1/8 6-29 66.00 638 10-Al-1 1-3/8 1-1/8 7/8 1/4 3-3/4 5/8 80
14 5-1/4 6-8387 66.00 644 6-Al-1 1 1-1/16 1/2 1/2 4-1/4 1/2
Typical
Frame
Number
38
See Table B2 on page 5 for blank fan machining charges.
For more photos please visit our website at www.jenkins.com