You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
moTor parTS<br />
EZE-SLEEVES®<br />
WIRE MARKERS<br />
EZE-SLEEVE®<br />
We stock the EZE-Sleeves® for our own in bushing bearing housings in end bells, for bushing bearing<br />
cartridges, and for bushing shaft holes. The EZE-Sleeve® is made of cast iron with a precision ground OD<br />
a few milimeters (mm) greater than the bearing OD, and rough machined ID a few milimeters (mm) less<br />
than the bearing OD. The first two or three digits of the EZE-Sleeve® catalog numbers are the bearing<br />
OD in milimeters. The last two digits of the catalog number are the EZE-Sleeve® length in milimeters. An<br />
exact OD is marked on each EZE-Sleeve® to the nearest thousandth of an inch, but we recommend that<br />
you use your own micrometers to verify the dimension. To use an EZE-Sleeve®, bore out the housing to<br />
0.002” smaller than the precision ground OD. This will provide a 0.002” interference fit. We also suggest<br />
you us an anaerobic adhesive/sealant to secure the EZE-Sleeve® in place. Finally, finish machining the<br />
ID per a standard bearing tolerance chart. ABEC-1 fits are shown: precision bearings require a tighter<br />
tolerance. EZE-Sleeve® length is greater than the bearing width to allow you to test bore the lip and<br />
check it with your micrometers before completing the final cut. This lip will be faced off after the<br />
bore is complete. We recommend leaving the bore below the minimum diameter and sanding a few<br />
thousandths off the bore to complete the bushing operation.<br />
<strong>Jenkins</strong><br />
<strong>Catalog</strong><br />
Number<br />
Redi-<br />
Sleeve<br />
Number<br />
List<br />
Price<br />
$<br />
Finish for<br />
Bearing<br />
Size Nos.<br />
Sleeve Length Nominal Bearing Housing Diameter<br />
(Minimum) Size (mm) Inches (ABEC-1)<br />
Inches mm O.D. Width Minimum Maximum<br />
M-3020 RS3020 $20.00 6200 13/16 20 30 9 1.1811 1.1816<br />
M-3220 RS3220 20.00 6201 13/16 20 32 12 1.2598 1.2604<br />
M-3520 RS3520 20.00 6202, 6300 13/16 20 35 11 1.3780 1.3786<br />
M-4020 RS4024 21.00 6203 13/16 20 40 12 1.5748 1.5754<br />
M-4720 RS4720 21.00 6204, 6303 13/16 20 47 14 1.8504 1.8510<br />
M-5222 RS5222 22.00 6205, 6304 7/8 22 52 15 2.0472 2.0479<br />
M-6230 RS6223 20.00 6206, 6305 1-1/8 30 62 16, 17 2.4409 2.4416<br />
M-6250 RS6250 30.00 6206, 6305 1-15/16 50 62 16, 17 2.4409 2.4416<br />
M-7230 RS7225 21.00 6207, 6306 1-1/8 30 72 17, 19 2.8346 2.8353<br />
M-8030 RS8026 24.00 6208, 6307 1-1/8 30 80 18, 21 3.1496 3.1503<br />
M-8050 RS8042 39.00 3508 2 50 80 30 3.1496 3.1503<br />
M-8540 RS8538 35.00 6209 1-9/16 40 85 19 3.3465 3.3474<br />
M-9040 RS9029 33.00 6210, 6308 1-9/16 40 90 20, 23 3.5433 3.5442<br />
M-10040 RS10031 35.00 6211, 6309 1-9/16 40 100 21, 25 3.9370 3.9379<br />
M-11040 RS11033 39.00 6212, 6310 1-9/16 40 110 22, 27 4.3307 4.3316<br />
M-11060 RS11060 48.00 6212, 6310 2-3/8 60 110 22, 27 4.3307 4.3316<br />
M-12040 RS12040 37.00 6213, 6311 1-9/16 40 120 23, 29 4.7244 4.7253<br />
M-12070 RS12070 57.00 6213, 6311 2-3/4 70 120 23, 29 4.7244 4.7253<br />
M-12540 RS12532 38.00 6214 1-9/16 40 125 24 4.9213 4.9223<br />
M-13040 RS13040 39.00 6215, 6312 1-9/16 40 130 25, 31 5.1181 5.1191<br />
M-13070 RS13062 59.00 3515, 3612 2-3/4 70 130 54 5.1181 5.1191<br />
M-14050 RS14041 50.00 6216, 6313 1-15/16 50 140 27, 33 5.5118 5.5128<br />
M-14070 RS14070 61.00 6216, 6313 2-3/4 70 140 27, 33 5.5118 5.5128<br />
M-15050 RS15043 51.00 6217, 6314 1-15/16 50 150 28, 35 5.9055 5.9065<br />
M-16050 RS16045 59.00 6218, 6315 1-15/16 50 160 30, 37 6.2992 6.3002<br />
M-16060 RS16060 70.00 6218, 6315 2-3/8 60 160 30, 37 6.2992 6.3002<br />
M-17050 RS17050 68.00 6219, 6316 1-15/16 50 170 32, 39 6.6929 6.6939<br />
M-18050 RS18050 73.00 6220, 6317 1-15/16 50 180 34, 41 7.0866 7.0876<br />
M-19050 RS19051 71.00 6221, 6318 1-15/16 50 190 36, 43 7.4803 7.4814<br />
M-20060 RS20053 90.00 6222, 6319 2-3/8 60 200 38, 45 7.8740 7.8751<br />
M-21560 RS21560 100.00 6224, 6320 2-3/8 60 215 47 8.4646 8.4657<br />
M-28080 RS28080 218.00 6326 3-5/32 80 280 80 11.0236 11.0247<br />
PLASTIC SLEEVE WIRE MARKERS<br />
<strong>Catalog</strong><br />
Number<br />
List Price<br />
Per Hundred<br />
Fits Wire O.D. Length of Fits Motor Lead<br />
Sleeve in Wire Sizes (AWG)<br />
Min. Max. Inches Loose Tight<br />
AFS-3* $9.00 100 200 16 22 18<br />
AFS-4* 11.00 140 250 20 20 12<br />
AFS-5* 13.00 210 350 22 16 10<br />
AFS-6* 15.00 320 480 22 10 4<br />
* Put the number you want printed on the band in this space. For instance, AFS-3-6<br />
is a white band for a size 20 lead wire with the number “6” printed on it. We stock the<br />
numbers 0-9. All are black markings printed on a white PVC flexible sleeve. Letters<br />
A through Z and other symbols are available on special orders at an increased price.<br />
Colored sleeves are also available at a premium price. We have used these markers<br />
on our rewinds, and they stood the varnish and baking cycles satisfactorily. Ask for<br />
a sample to try on your own leads. They last better than adhesive number strips,<br />
and they are non-conducting.<br />
Because of recurring price changes, Please CALL for OEM List Prices.<br />
For additional information please visit our website at www.jenkins.com<br />
71
Change language