SPARC Enterprise T5120 and T5220 Servers Service Manual - Fujitsu

More documents

Recommendations

Info

FIGURE: Front Panel Controls and Indicators on SPARC Enterprise T5120 Servers Figure Legend 1 Locator LED and button 5 Hard Drive map 2 Service Required LED 6 Power Supply Service Required LED 3 PowerOKLED 7 Overtemp LED 4 Power button 8 Fan Module Service Required LED 6 SPARC Enterprise T5120 and T5220 Servers Service Manual • July 2009
The following table provides descriptions of these controls and indicators. TABLE: Front Panel Controls and Indicators (SPARC Enterprise T5120 and T5220 Servers) LED or Button Icon or Label Description Locator LED and button (white) Service Required LED (amber) Power OK LED (green) The Locator LED can be turned on to identify a particular system. When on, it blinks rabidly. There are three methods for turning a Locator LED on: • Issuing the ILOM command set /SYS/LOCATE value=Fast_Blink • Issuing the ALOM CMT command setlocator on. • Pressing the Locator button. If on, indicates that service is required. POST and ILOM are two diagnostics tools that can detect a fault or failure resulting in this indication. The ILOM show faulty command provides details about any faults that cause this indicator to light. Under some fault conditions, individual component fault LEDs are lit in addition to the system Service Required LED. Provides the following indications: • Off – System is not running in its normal state. System power might be off. The service processor might be running. • Steady on – System is powered on and is running in its normal operating state. No service actions are required. • Fast blink – System is running in standby mode and can be quickly returned to full function. • Slow blink –A normal, but transitory activity is taking place. Slow blinking might indicate that system diagnostics are running, or the system is booting. Power button The recessed Power button toggles the system on or off. • Press once to turn the system on. • Press once to shut the system down in a normal manner. • Press and hold for 4 seconds to perform an emergency shutdown. Power Supply Fault LED (amber) Overtemp LED (amber) Fan Fault LED (amber) REAR PS TOP FAN Provides the following operational PSU indications: • Off – Indicates a steady state, no service action is required. • Steady on – Indicates that a power supply failure event has been acknowledged and a service action is required on at least one PSU. Provides the following operational temperature indications: • Off – Indicates a steady state, no service action is required. • Steady on – Indicates that a temperature failure event has been acknowledged and a service action is required. Provides the following operational fan indications: • Off – Indicates a steady state, no service action is required. • Steady on – Indicates that a fan failure event has been acknowledged and a service action is required on at least one of the fan modules. Identifying Server Components 7
Page 3 and 4: Manual Code C120-E463-04EN Part No.
Page 5: Copyright © 2009 Sun Microsystems,
Page 8 and 9: How to Switch From the System Conso
Page 10 and 11: ▼ Remove the Top Cover 67 Servici
Page 12 and 13: Servicing Power Supplies 129 Power
Page 14 and 15: HDD Data Cable Routing for SAS RAID
Page 16 and 17: Structure and Contents of This Manu
Page 18 and 19: Title Description Manual Code SPARC
Page 20 and 21: Prompt Notations The following prom
Page 22 and 23: Task Warning Maintenance Damage The
Page 24 and 25: Product Handling Maintenance Warnin
Page 26 and 27: Fujitsu Welcomes Your Comments If y
Page 28 and 29: Infrastructure Boards in SPARC Ente
Page 30 and 31: Board Description Hard drive backpl
Page 34 and 35: Related Information ■ “LED Over
Page 36 and 37: FIGURE: Front Panel Controls and In
Page 38 and 39: Related Information ■ “LED Over
Page 40 and 41: Status LEDs for Ethernet Ports and
Page 42 and 43: ■ Power-on self-test (POST) - POS
Page 44 and 45: FIGURE: Diagnostics Flowchart 18 SP
Page 46 and 47: TABLE: Diagnostic Flowchart Referen
Page 48 and 49: TABLE: System Faults and the Corres
Page 50 and 51: Note - No ILOM command is needed to
Page 52 and 53: Service-Related ILOM Command Summar
Page 54 and 55: TABLE: Service-Related Commands (Co
Page 56 and 57: Example of show faulty Output When
Page 58 and 59: ▼ Display FRU Information With th
Page 60 and 61: 3. Log out of the root account afte
Page 62 and 63: Note - The value of keyswitch_state
Page 64 and 65: Note - When you change individual P
Page 66 and 67: -----------------------------------
Page 68 and 69: 2. Clear the fault by setting the F
Page 70 and 71: Solaris PSH Feature Overview The So
Page 72 and 73: 1. Check the event log using the fm
Page 74 and 75: 3. Use the clear_fault_action prope
Page 76 and 77: The database that contains the list
Page 78 and 79: -> start /SYS Are you sure you want
Page 80 and 81: FIGURE: SunVTS Browser Interface 4.
Page 82 and 83:
56 SPARC Enterprise T5120 and T5220
Page 84 and 85:
Caution - There is a risk of person
Page 86 and 87:
Properties: type = Host System keys
Page 88 and 89:
▼ Power Off the Server (Power But
Page 90 and 91:
FIGURE: Slide Release Latches 4. Wh
Page 92 and 93:
4. From the front of the server, pu
Page 94 and 95:
FIGURE: Removing the Top Cover 3. R
Page 96 and 97:
If either of these conditions exist
Page 98 and 99:
1. At the Solaris prompt, type the
Page 100 and 101:
Note - SPARC Enterprise T5120 serve
Page 102 and 103:
7. At the Solaris prompt, type the
Page 104 and 105:
Eight-Drive Capable Backplane Confi
Page 106 and 107:
TABLE: Physical Drive Locations, FR
Page 108 and 109:
Memory Fault Handling Overview A va
Page 110 and 111:
Note - The FB-DIMM Fault Locator bu
Page 112 and 113:
FIGURE: Removing FB-DIMMs 6. Press
Page 114 and 115:
FIGURE: Installing FB-DIMMs 7. Alig
Page 116 and 117:
-> start /SYS Are you sure you want
Page 118 and 119:
Caution - You must disconnect the p
Page 120 and 121:
-> start /SYS Are you sure you want
Page 122 and 123:
FB-DIMM Configuration Reference The
Page 124 and 125:
The following table maps FB-DIMM lo
Page 126 and 127:
Related Information ■ “Identify
Page 128 and 129:
Servicing PCIe/XAUI Risers These to
Page 130 and 131:
FIGURE: Removing the PCIe/XAUI Rise
Page 132 and 133:
5. Engage the two captive Phillips
Page 134 and 135:
FIGURE: Installing a PCIe Card (SPA
Page 136 and 137:
11. Connect the power supplies. See
Page 138 and 139:
Related Information ■ “Remove a
Page 140 and 141:
▼ Install a Battery 1. Unpack the
Page 142 and 143:
Note - The server will not function
Page 144 and 145:
Note - The firmware configuration v
Page 146 and 147:
FIGURE: Removing the Motherboard As
Page 148 and 149:
6. If you are installing a new moth
Page 150 and 151:
Fan Module Configurations for SPARC
Page 152 and 153:
1. Extend the server to the mainten
Page 154 and 155:
FIGURE: Installing a Fan Module 2.
Page 156 and 157:
FIGURE: Power Supply LEDs (SPARC En
Page 158 and 159:
FIGURE: Cable management Arm Releas
Page 160 and 161:
▼ Install a Power Supply 1. Align
Page 162 and 163:
7. At the ALOM CMT sc> prompt, type
Page 164 and 165:
TABLE: Components That Require Remo
Page 166 and 167:
2. Unplug the power cords. See “D
Page 168 and 169:
FIGURE: Installing the DVD/USB Modu
Page 170 and 171:
2. Disconnect the power cables. See
Page 172 and 173:
Related Information ■ “Remove t
Page 174 and 175:
FIGURE: Removing a Hard Drive Cage
Page 176 and 177:
FIGURE: Installing a Hard Drive Cag
Page 178 and 179:
14. Power on the system. See “Pow
Page 180 and 181:
FIGURE: Removing a Hard Drive Backp
Page 182 and 183:
FIGURE: Installing a Hard Drive Bac
Page 184 and 185:
FIGURE: Removing the Front Control
Page 186 and 187:
Servicing Power Distribution Boards
Page 188 and 189:
FIGURE: Removing a Power Distributi
Page 190 and 191:
FIGURE: Installing a Power Distribu
Page 192 and 193:
FIGURE: Installing a Power Supply i
Page 194 and 195:
Power Supply Backplane Overview The
Page 196 and 197:
Related Information ■ “Install
Page 198 and 199:
Paddle Card Overview The paddle car
Page 200 and 201:
Page 202 and 203:
FIGURE: Installing the Top Cover No
Page 204 and 205:
FIGURE: Release Tabs on the Rail 2.
Page 206 and 207:
▼ Power On the Server Using the F
Page 208 and 209:
Motherboard Components in T5120 Ser
Page 210 and 211:
I/O Components in SPARC Enterprise
Page 212 and 213:
Power Distribution/Fan Module Compo
Page 214 and 215:
Internal Cables for Onboard SAS Con
Page 216 and 217:
FIGURE: Internal Cables for the Onb
Page 218 and 219:
FIGURE: Hard Drive Data Cable Routi
Page 220 and 221:
FIGURE: Hard Drive Data Cable Routi
Page 222 and 223:
Motherboard Components in T5220 Ser
Page 224 and 225:
I/O Components in SPARC Enterprise
Page 226 and 227:
Power Distribution/Fan Module Compo
Page 228 and 229:
Internal Cables for Onboard SAS Con
Page 230 and 231:
FIGURE: Internal Cables for the Onb
Page 232 and 233:
HDD Data Cable Routing for SAS RAID
Page 234 and 235:
Page 236 and 237:
fan power board FRU name, 187, 201
Page 238:
emoving, 67 topic guidelines, 1, 15
show all

SPARC Enterprise T5120 and T5220 Servers Service Manual - Fujitsu

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?