Manual - Leybold Repair by Tech Services

Recommendations

Info

Head 22 ⏐GA10218_0101 - 5/2002 2.2.2.2 Digital Out (Control) The following relay outputs Fig. 3/8 are available for further signal processing. The maximum rating for the relay contacts is 60V AC/1A. The contacts are numbered from bottom to top. Pin Assignment 1 PLC in free selectable 2 PLC in free selectable 3 PLC in free selectable 4 GND 5 to 7 Digital out free selectable, 5 center contact, 6 normally open contact, 7 normally closed contact 8 to 10 Digital out free selectable 11 to 13 Digital out free selectable 14 to 16 Digital out free selectable The pin assignment for contacts 8 to 16 follows the same order as for pins 5 to 7. For further information see chapter 6.6.4.4 2.2.2.3 Digital In (Control 2) These inputs can be used to control the PhoeniXL with a programmable logic control (PLC). Pin Assignment 1 PLC in free selectable 2 PLC in free selectable 3 PLC in free selectable 4 PLC GND These inputs Fig. 3/6 are working only, if the correct location of control is chosen. See chapter 6.6.4.1 To avoid a mistake between the connection Control 2 and Record, pin 1 and 4 are blocked. When using the connectors the guiding nose for pin 1 and 4 must be removed. For further information see chapter 6.6.4.5
2.2.2.4 Recorder The recorder output Fig. 3/7 may be used to chart the leak rate, the inlet pressure and the forevacuum pressure. Both recorder activities can be adjusted individually for showing leak rates and pressures. The measured values are provided <strong>by</strong> way of an analogue signal in the range of 0 V … 10 V. The resolution is limited to 10 mV. The instrument which is connected to the recorder output (e. g. X(t) chart recorder) should have an input resistance of no less than 2.5 kΩ. The measured values are available through pins 1 and 4. The reference potential (GND) is available at pins 2 and 3. The contacts are numbered from bottom to top. The chart recorder outputs are electrically isolated from other plugs. If, in spite of this, hum interference is apparent it is recommended to operate the PhoeniXL and the chart recorder from the same mains phase. If this is not possible, you must make sure that the frame ground of both instruments is kept at the same potential. Pin Assignment 1 Analog 1, leak rate, inlet pressure P1 or forevacuum pressure P2 2 GND 3 GND 4 Analog 2, leak rate, inlet pressure P1 or forevacuum pressure P2 For further information see chapter 6.6.4.2 and 6.6.4.6. 2.2.2.5 RS232 This RS232 interface Fig. 3/5 is wired as data communication equipment (DCE) and permits the connection of a personal computer (PC) for monitoring and data logging. The connection is made through a 9 pin sub-D sokket. For more information refer to chapter 6.6.4.3 and the Interface Description. Pin Assignment 1 24 V switchable, default setting 0 2 TXD 3 RXD 4 GND 24V 5 GND 6 DSR 7 CTS 8 RTS 9 free Head GA10218_0101 - 5/2002 ⏐ 23
Page 1 and 2: Operating Instructions GA10218_0102
Page 3 and 4: Head 2 Installation ...............
Page 5 and 6: Head 6.3 Mode .....................
Page 7 and 8: Head 7.3 Factor of Calibration - Ra
Page 9 and 10: 1.1.4 Definiton of Terms The range
Page 11 and 12: 1.3 Introduction 1.3.1 Purpose The
Page 13 and 14: 1.3.2.3 Other Data Valves solenoid
Page 15 and 16: 300 Modul 1.3.4 Technical Data Phoe
Page 17 and 18: � Blank flange DN 25 KF � Clamp
Page 19 and 20: 2 Installation 2.1 Working Location
Page 21: Fig. 3 Side views of the PhoeniXL L
Page 25 and 26: of these gas line must not exceed 1
Page 27 and 28: 3 First Operation Check The steps f
Page 29 and 30: 3.2.3 Verification with an external
Page 31 and 32: Pos. Description 4 Fore pressure pu
Page 33 and 34: P 2 external pump 2 7 4 1 V 6 V 2a
Page 35 and 36: 4.1.2.4 ZERO Button Pushing the ZER
Page 37 and 38: Fig. 11 Numerical entry of the Trig
Page 39 and 40: 4.1.4 Partial Flow Method In the pa
Page 41 and 42: level is taken over anew, provided
Page 43 and 44: 5 Operation of the PhoeniXL The Pho
Page 45 and 46: Fig. 14 Display: Measurement Mode w
Page 47 and 48: 6 Description of the Menu By pressi
Page 49 and 50: Explanation to figure 16: Key No. N
Page 51 and 52: 6.2.2 Display-range auto/manual �
Page 53 and 54: the net leak rate from the part und
Page 55 and 56: 6.4.1 Trigger Level 1 � Main menu
Page 57 and 58: 6.4.6 Alarm delay � Main menu > T
Page 59 and 60: 6.5 Calibration � Main menu > Cal
Page 61 and 62: 6.6.1 Vacuum settings � Main menu
Page 63 and 64: Softkey 2: Immediately The inlet po
Page 65 and 66: Softkey 2: ↓ The entry of the nom
Page 67 and 68: Since the effective pumping rates a
Page 69 and 70: 6.6.3 Mass � Main menu > Settings
Page 71 and 72: The fundamental output voltage is s
Page 73 and 74:
Description of operation mode of th
Page 75 and 76:
Softkey 2: Time&Date See chapter 6.
Page 77 and 78:
Softkey 3: ↓ Decrease of the serv
Page 79 and 80:
Softkey No. 2: ↓ Decrease change
Page 81 and 82:
6.7 Information � Main menu > Inf
Page 83 and 84:
6.8.2 Change Menu-PIN � Main menu
Page 85 and 86:
After External Calibration ( Fig. 2
Page 87 and 88:
8 Error And Warning Messages The Ph
Page 89 and 90:
No. Displayed Message Description a
Page 91 and 92:
Head No. Displayed Message Descript
Page 93 and 94:
No. Displayed Message Description a
Page 95 and 96:
9.1.2 Opening the PhoeniXL 2 3 Fig.
Page 97 and 98:
egulations for the safety of the en
Page 99 and 100:
TMP-converter TDS Fig. 37 assembly
Page 101 and 102:
Appendix A B C D F G I L M Ambient
Page 103 and 104:
Abmessungen PhoeniXL Familie in mm
Page 105 and 106:
Fig. 4 Declaration of Conformance H
Page 107 and 108:
Head GA10218_0101 - 9/2002 ⏐ 108
show all

Manual - Leybold Repair by Tech Services

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?