Manual - Leybold Repair by Tech Services

Recommendations

Info

Head 26 ⏐GA10218_0101 - 5/2002 Pressure: mbar Minimum volume: 0 Beep: on Maximum evacuation time: 30 minutes Audio Alarm Type: Trigger Alarm Max. pressure limit for sniff mode 0.15 mbar Min. pressure limit for sniff mode 0.05 mbar Control location local Alarm delay: 30 seconds Leak rate filter: auto Zero: enable Vacuum ranges normal Upper display limit 1E-5 mbar l/s Service message exhaust oil filter (PhoeniXL 300 only) on
3 First Operation Check The steps for an initial operation are described in this chapter. It is explained how to switch on the PhoeniXL, how to measure and how to carry out an internal calibration. If anything unexpected happens during the initial operation or the leak detector acts in a strange way the PhoeniXL can be switched off by the mains switch at any time. 3.1 Needed Equipment The following parts will be needed: � A blind flange 25 KF (if not preassembled at the inlet port). � A helium test leak with a DN 25 KF connection (optional). � A forevacuum pump connected to the DN25 KF flange on the side or under the bottom (dry or wet version) for use with the PhoeniXL 300 Modul 3.2 Description of the Initial Operation Please proceed the following description step by step to start the initial operation. Refer to Chapter 5 for a more detailed description. 3.2.1 Startup and Measure 1. Unpack the PhoeniXL and inspect it for any external damage (refer to Chapter 1.4). 2. Connect the instrument to the mains power (Refer to Chapter 2.2.1). For the PhoeniXL 300 Modul connect the forevacuum pump and switch it on. 3. Switch on the PhoeniXL by using the mains switch Fig. 3/4. Don’t switch the PhoeniXL on when ambient temperature is below 10°C or above 40°C. After power on a welcoming picture appears on the screen of the control panel Fig. 4/1, the status information on the speed of the turbo pump, the foreline pressure, the emission and the active filament are given. The start up procedure takes less than 2 minutes and the end is indicated by a signal. The PhoeniXL is in Stand-by mode now.(Fig. 4) 4. Check if the inlet port is blanked off. If not, please mount a blind flange with o-ring on the inlet port. Head Caution GA10218_0101 - 5/2002 ⏐ 27
Page 1 and 2: Operating Instructions GA10218_0102
Page 3 and 4: Head 2 Installation ...............
Page 5 and 6: Head 6.3 Mode .....................
Page 7 and 8: Head 7.3 Factor of Calibration - Ra
Page 9 and 10: 1.1.4 Definiton of Terms The range
Page 11 and 12: 1.3 Introduction 1.3.1 Purpose The
Page 13 and 14: 1.3.2.3 Other Data Valves solenoid
Page 15 and 16: 300 Modul 1.3.4 Technical Data Phoe
Page 17 and 18: � Blank flange DN 25 KF � Clamp
Page 19 and 20: 2 Installation 2.1 Working Location
Page 21 and 22: Fig. 3 Side views of the PhoeniXL L
Page 23 and 24: 2.2.2.4 Recorder The recorder outpu
Page 25: of these gas line must not exceed 1
Page 29 and 30: 3.2.3 Verification with an external
Page 31 and 32: Pos. Description 4 Fore pressure pu
Page 33 and 34: P 2 external pump 2 7 4 1 V 6 V 2a
Page 35 and 36: 4.1.2.4 ZERO Button Pushing the ZER
Page 37 and 38: Fig. 11 Numerical entry of the Trig
Page 39 and 40: 4.1.4 Partial Flow Method In the pa
Page 41 and 42: level is taken over anew, provided
Page 43 and 44: 5 Operation of the PhoeniXL The Pho
Page 45 and 46: Fig. 14 Display: Measurement Mode w
Page 47 and 48: 6 Description of the Menu By pressi
Page 49 and 50: Explanation to figure 16: Key No. N
Page 51 and 52: 6.2.2 Display-range auto/manual �
Page 53 and 54: the net leak rate from the part und
Page 55 and 56: 6.4.1 Trigger Level 1 � Main menu
Page 57 and 58: 6.4.6 Alarm delay � Main menu > T
Page 59 and 60: 6.5 Calibration � Main menu > Cal
Page 61 and 62: 6.6.1 Vacuum settings � Main menu
Page 63 and 64: Softkey 2: Immediately The inlet po
Page 65 and 66: Softkey 2: ↓ The entry of the nom
Page 67 and 68: Since the effective pumping rates a
Page 69 and 70: 6.6.3 Mass � Main menu > Settings
Page 71 and 72: The fundamental output voltage is s
Page 73 and 74: Description of operation mode of th
Page 75 and 76: Softkey 2: Time&Date See chapter 6.
Page 77 and 78:
Softkey 3: ↓ Decrease of the serv
Page 79 and 80:
Softkey No. 2: ↓ Decrease change
Page 81 and 82:
6.7 Information � Main menu > Inf
Page 83 and 84:
6.8.2 Change Menu-PIN � Main menu
Page 85 and 86:
After External Calibration ( Fig. 2
Page 87 and 88:
8 Error And Warning Messages The Ph
Page 89 and 90:
No. Displayed Message Description a
Page 91 and 92:
Head No. Displayed Message Descript
Page 93 and 94:
No. Displayed Message Description a
Page 95 and 96:
9.1.2 Opening the PhoeniXL 2 3 Fig.
Page 97 and 98:
egulations for the safety of the en
Page 99 and 100:
TMP-converter TDS Fig. 37 assembly
Page 101 and 102:
Appendix A B C D F G I L M Ambient
Page 103 and 104:
Abmessungen PhoeniXL Familie in mm
Page 105 and 106:
Fig. 4 Declaration of Conformance H
Page 107 and 108:
Head GA10218_0101 - 9/2002 ⏐ 108
show all

Manual - Leybold Repair by Tech Services

Create successful ePaper yourself

Delete template?

Save as template?