ASTi Model Builder Visual Basic Training Manual Document: DOC ...

More documents

Recommendations

Info

Figure 19: RMS Telestra Status Page ASTi MBV Telestra Training (Ver.1, Rev.B) 18 Copyright © 2006 Advanced Simulation Technology inc.
ASTi MBV Telestra Training (Ver.1, Rev.B) 4.0 DIS 4.1. DIS Interface The DIS interface carries the radio, network intercom, voice and data traffic, which is generated and received by Model Builder Visual. Within MBV each asset can be set to DIS or local only operation. This allows the user to have the ability to define DIS radios up to the processing limits of the platform. Global DIS settings can be configured through RMS. DIS Radio Basics Network configuration: • To communicate over DIS, this feature must be enabled by ASTi in your options file. • You need two DIS enabled network products (Telestra, DACS, PC’ver). • Local IP address and Mask • Broadcast or multicast IP address • UDP port • Checksum parameters and DIS PDU timeout values • DIS Site and Host Values • Other/Advanced Model configuration: • Ensure the DIS IDs are unique and radios are in the same exercise. • Match modulation type, frequency, Bandwidth, modulation, crypto state, Frequency Hopping/HQ settings, etc. for the radios. • MBV decodes incoming audio based on signal PDU. • Support of multiple simultaneous exercises (up to 255). DIS PDU Types While this is a course on the Telestra and MBV software, it is important to understand the DIS interface traffic and its characteristics. When the DIS interface is used to carry model communications information the packet format is “IP|UDP|DIS_PDU” over standard Ethernet. The UDP port setting is configured through RMS. The DIS PDUs contain all of the pertinent information such as: • Voice communication • Tactical Data communication • Radio Parameters (frequency, location, Tx power, DIS IDs, exercise #, etc.) Copyright © 2006 Advanced Simulation Technology inc. 19
Page 1: ASTi Model Builder Visual Basic Tra
Page 5 and 6: Table of Contents 1.0. Introduction
Page 7 and 8: 6.8. Configuring Model Network Sett
Page 9 and 10: 9.4. Tutorial 4- Mixer and Channel
Page 11 and 12: ASTi MBV Telestra Training (Ver.1,
Page 27: ASTi MBV Telestra Training (Ver.1,
Page 79 and 80:
ASTi MBV Telestra Training (Ver.1,
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167:
show all

ASTi Model Builder Visual Basic Training Manual Document: DOC ...

Create successful ePaper yourself

Delete template?

Save as template?