ASTi Model Builder Visual Basic Training Manual Document: DOC ...

More documents

Recommendations

Info

6.3. Configure Basic Settings ASTi MBV Telestra Training (Ver.1, Rev.B) RMS allows user to enter basic information that identifies and describes a Telestra platform. The Telestra >> Preferences screen shows the system’s basic settings, such as installation and contact information. It also provides the ability to add and delete Telestra user accounts, which are important in MBV model management. Settings include: • Description (e.g. Comms Telestra) • Installation Facility (e.g. NLX Corporation) • Installation Location (e.g. Sterling, VA) • Installation Trainer (e.g. E-2C WST) • Contact Name • Contact Phone • Contact Email Figure 21:Telestra System Status 26 Copyright © 2006 Advanced Simulation Technology inc.
ASTi MBV Telestra Training (Ver.1, Rev.B) 6.4. Network Settings RMS allows the user to configure the following network settings on the Telestra platform. • General Networking. This section encompass network-wide, interface-independent settings such as Autodiscovery, DNS nameserver and router gateway IP addresses. • Time Server. This section allows you to specify and test connection to a network time server (NTP server) for synchronizing Telestra’s internal clock. Other settings allow you to tweak Telestra’s NTP client variables. • Ping Utility. Enter another computer’s hostname or IP address to send five pings (echo requests) to it. Positive response indicates that computer is reachable over the network, using any of Telestra’s three network interfaces. • Network Interfaces. These sections allow you to specify IP address, card mode and subnet mask for each of Telestra’s three Ethernet interface cards. Operational Warning: Making changes to the interface settings (especially eth0), such as changing manual IP address, or setting card mode to DHCP may result in your not being able to access RMS at the original (previous) IP address. If you change these settings, you must then specify the new IP address in your browser’s Address slot to access RMS at its new network location. Copyright © 2006 Advanced Simulation Technology inc. 27
Page 1: ASTi Model Builder Visual Basic Tra
Page 5 and 6: Table of Contents 1.0. Introduction
Page 7 and 8: 6.8. Configuring Model Network Sett
Page 9 and 10: 9.4. Tutorial 4- Mixer and Channel
Page 11 and 12: ASTi MBV Telestra Training (Ver.1,
Page 35: ASTi MBV Telestra Training (Ver.1,
Page 87 and 88:
ASTi MBV Telestra Training (Ver.1,
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167:
show all

ASTi Model Builder Visual Basic Training Manual Document: DOC ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?