TRILUX Luminaires - Proljus AB
TRILUX Luminaires - Proljus AB
TRILUX Luminaires - Proljus AB
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Maxilux<br />
Compact Floodlight<br />
65a IP65<br />
Compact floodlight with pseudo rotationally<br />
symmetrical light distribution.<br />
Floodlight housing<br />
made of an anodised aluminium reflector<br />
and an anthracite base made of die-cast<br />
aluminium, additionally anodised. With<br />
flange-mounted, thermally decoupled ignitor<br />
tray and pressure equalisation vent.<br />
Cover made of 5 mm thick, thermally toughened<br />
safety glass, equipped with a silicon<br />
seal and held secure to the reflector part<br />
using non-rusting clips, a mesh cover is not<br />
necessary.<br />
Fixing bracket made of galvanised steel,<br />
continuously adjustable, suited for upright<br />
and suspended mounting of floodlight.<br />
Optical systems<br />
The aluminium reflector forms the rotationally<br />
symmetrical reflector, which has a<br />
highly-specular or semi-specular anodised<br />
inner surface. With internal highly-specular<br />
shield. Pseudo rotationally symmetrical light<br />
distribution.<br />
154<br />
T narrow-angle, reflector highly-specular.<br />
TB narrow/wide-angle, reflector highlyspecular.<br />
B wide-angle, reflector semi-specular.<br />
SB extremely wide-angle, reflector semispecular.<br />
Re-lamping is simple after loosening four<br />
captive stainless steel screws and opening<br />
the back cover with mounted fixture and<br />
reflector components.<br />
Electrical connection<br />
using enclosed, lockable connector with<br />
cable gland Pg13.5, with 4-pole terminal for<br />
wires up to 2.5 mm². When opening the housing<br />
to change the lamp, the connector must<br />
be unplugged and the floodlight must be<br />
disconnected from power supply.<br />
Versions with ignitor, optionally for instantaneous<br />
hot re-ignition (WZ). Others components<br />
required for operating the floodlight<br />
must be ordered separately and mounted,<br />
see Accessories.<br />
7-420···<br />
WZ versions with attached, intelligent ignition<br />
management system for instantaneous<br />
hot re-ignition of lamp after power outage.<br />
State-of-the-art microprocessor technology<br />
allows for flicker-free and lamp-preserving<br />
rapid lamp start of even hot lamps. Automatic<br />
safety cut-off and end-of-life detection<br />
prevent abnormal lamp operation and protect<br />
the components of the luminaire. The<br />
floodlight is connected to the ignitor via a<br />
3-pole terminal of up to 4 mm². With cable<br />
gland M20 for cables up to 8 - 13 mm.<br />
Windage area F W = 0.16 m 2 .<br />
Control gear box 0860GK···, either for one<br />
or two floodlights, made of sheet steel, lightgrey,<br />
similar to RAL 7035, powder-coated,<br />
weather-resistant. With lockable door.<br />
Complete with all necessary control gear,<br />
prewired ready for connection. With two or<br />
three cable glands M20 for cables up to<br />
6-12 mm. Mains-side connection terminal<br />
5 x 6 mm², luminaire-side terminals<br />
2 x 3 x 6 mm². Parallel-compensated.<br />
Safety class I, degree of protection IP65.<br />
Supply unit 0860VE··· for one floodlight<br />
including Neozed fuse 16 A and 8-pole<br />
screw-type terminal 6 mm². With two cable<br />
glands M20 for cables up to 7-14 mm. Fixed<br />
via two boreholes 12 mm. Parallel-compensated.<br />
Safety class I, degree of protection<br />
IP65.