2600 Test-A Pack System

More documents

Recommendations

Info

4.3 Start the creep test. 4.4 Allow the console time to stabilize at the creep pressure. (Small fluctuations in pressure are due to the lack of volume in the pressure manifold.) 5.0 Verification of Calibration 5.1 After reaching a stable creep pressure verify the calibration of the 2600 by comparing the pressures displayed on the 2600 console and the calibration standard (Figures 5 and 6). 5.2 The pressures should be within 2.77 in H2O (0.1 psi) of each other. 5.3 Disconnect the Calibration Standard, associated tubing and the Pressure Manifold. Carleton Technologies Inc. doing business as Cobham Life Support VI
QUESTIONS AND ANSWERS Q. Air is escaping around the needle on the closed package test fixture; will it effect the test results? A. The sensing line is used to monitor the pressure inside the package. Escaping air will have no effect on the measurement of internal pressure. Q. What test parameters should be used on my pouch or tray to perform a burst test? A. We find that the factory setting FLOW=5, and SENSITIVITY=1 with PREFILL= YES will test a wide range of commercially available products. Q. What is the function of PREFILL? A. PREFILL is used to fill up a pouch or tray to a sense value of 1 inch of water pressure. This is done so that the seals of the pouch/tray will not be shocked by excessive pressure rise rates. Q. What test standard does the burst test conform to? A. ASTM F1140 Standard Test Methods for Internal Pressurization Failure Resistance of Unrestrained Packages for Medical Applications. Q. What is the correlation between the burst test and a peel test? A. There is no direct mathematical relationship between a burst test and a peel test. A carefully prepared test procedure using both methods, and comparing the test results is the preferred method of correlation. Q. Will the control console identify channels or pin holes in my package? A. No, the control console cannot distinguish between porosity, pinholes or channels. Q. Can any printer be used with the F100-2600 console? A. No, only certain continuous feed printers will work with the console. The optional Test-A-Pack F100-2573-1 printer kit (or F100-2573-4 for 220V) is recommended for use with this system. Carleton Technologies Inc. doing business as Cobham Life Support VII
Page 1 and 2: Carleton Technologies Inc. doing bu
Page 3 and 4: Table of Contents CAUTIONS AND NOTI
Page 5 and 6: CAUTIONS AND NOTICES The following
Page 7 and 8: PREFACE About This Guide This is yo
Page 9 and 10: CHAPTER 1: INTRODUCTION TO THE F100
Page 11 and 12: Front Panel Figure 1: Front Panel F
Page 13 and 14: PORT 3- Pressure from an inflated p
Page 15 and 16: CHAPTER 2: 2600 SYSTEM SET UP In th
Page 17 and 18: Connecting Package Testing Fixtures
Page 19 and 20: CHAPTER 3 OPERATING INSTRUCTIONS In
Page 21 and 22: Package Testing Burst Test Before y
Page 23 and 24: a. Press the UP or DOWN arrow until
Page 25 and 26: c. Press the UP or DOWN arrow until
Page 27 and 28: . Press SET. The first digit of the
Page 29 and 30: Figure 13 c. Press the UP or DOWN a
Page 31 and 32: Baud Rate Selection Screen a. Press
Page 33 and 34: d. Press the UP or DOWN arrow to ch
Page 35 and 36: Prefill Override If the porosity or
Page 37 and 38: APPENDIX A: 2600 CONTROL UNIT SPECI
Page 39 and 40: APPENDIX B: CALIBRATION VERIFICATIO
Page 41: 3.4 Connect a length of 1/4” poly
Page 45 and 46: GLOSSARY OF TERMS (CONTINUED) Paral
Page 47 and 48: C.E. CERTIFICATION Carleton Technol
Page 49 and 50: OPTIONAL ACCESSORIES Open Package T
Page 51: CONTACT INFORMATION For more inform

2600 Test-A Pack System

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?