WARRANTY SSW-05 Plus - Dimotec

More documents

Recommendations

Info

ENGLISH 13. OPERATION OF THE DIGITAL RELAY OUTPUTS: t t Relay On t The relay of the Operation Function closes its N.O. contact (13-14/23) always when the SSW-05 Plus receives the enable command. This contact is open only at the end of the deceleration ramp (when it is set via trimpot) or when the SSW-05 Plus receives the disable command. The relay of the Full Voltage Function closes the N.O. contact (14/23-24) always when the SSW-05 Plus applies 100% voltage to the driven motor. This contact opens when the SSW-05 Plus receives the disable command. English-10
ENGLISH 14. PROTECTIONS AND DISPLAYS: Protection/Display Description Overcurrent* Phase Loss* Locked Rotor* Motor overload protection* Overcurrent of the SSW-05 Plus By-pass relay Overcurrent before By-pass Thyristor overload Frequency out of Tolerance Internal By-pass relay contact is open Display LED (overcurrent) LED (Phase Loss) Incorrect Phase LED Sequence* (Phase Seq) Undervoltage in the Control Supply Ready to operate In Operation LED (Stall) LED (Overload) LED (Internal Fault) LED Internal Fault) LED (Internal Fault) LED (Internal Fault) LED (Internal Fault) LED (Internal Fault) LED (Ready) LED (Run) Activation Monitoring is activated only when the SSW-05 Plus is in rated duty (100% voltage). It trips, when the motor current exceeds 3 times the value set with the trimpot (Motor Current) during a time longer than 1 second. It trips after 1s elapses with phase loss, both at the input and at the output (Motor). It trips when the current flowing through the SSW-05 is lower than 30% of the current set with trimpot (Motor Current). The error trips when in incorrect phase sequence. This protection trips during the transition between the end of the acceleration ramp time and the contact closure of the internal by-pass relays of the SSW-05 Plus, when the current flowing through the SSW-05 Plus is higher than or equal to 2 times the current set with trimpot (Motor Current). This protection monitors constantly the motor current and compares it with the value set by the trimpot (Motor Current). See Item 15. This protection monitors only when SSW-05 Plus is operating at full voltage (100%). It trips when the current becomes higher than 2 times the rated current of the SSW-05 Plus and is present for more than 1 second. The internal fault LED flashes 5 times intermittently. This protection trips during the transition between the end of the acceleration ramp time and the contact making of the internal bypass relays of the SSW-05 Plus, when the current flowing through the SSW-05 Plus is higher or equal to 2 times the rated current of the SSW-05 Plus. The internal fault LED flashes 4 times intermittently. This protection monitors the current that flows through the SSW-05 Plus during the acceleration and deceleration ramp time, and compares it with the rated current of the SSW-05 Plus. Fig. 15.2 shows the trip time curves when thyristors are overloaded. The internal fault LED flashes 6 times intermittently. This protection trips when the line frequency is out of range (+/- 10%), when compared with the rated frequency (50 Hz or 60Hz). The internal fault LED flashes 1 time intermittently. This protection monitors, if the contact of the internal by-pass relay of the SSW-05 Plus is closed ( it operates only when the SSW-05 Plus is operated at full voltage (100%). The internal fault LED flashes 3 times intermittently. This protection monitors the control supply voltage of the electronics (A1 and A2) constantly and trip always when Vac voltage become lower than 80% of the rated voltage. The internal fault LED flashes 2 times intermittently. - ON: SSW-05 Plus has been powered, and is waiting for the enable command, or with full voltage at output. - Flashing: SSW-05 Plus in acceleration/deceleration ramp time. It is On only when SSW-05 Plus is operating (motor is operating with full voltage). * These protections may be enabled/disabled through the respective dip-switches. English-11
Page 2 and 3: ENGLISH SUMMARY - English 1. Safety
Page 4 and 5: ENGLISH 4. TECHNICAL DATA: AC Input
Page 6 and 7: ENGLISH 8. CAPACITY OF THE POWER SU
Page 8 and 9: ENGLISH 11.3. Start/Stop by using P
Page 12 and 13: ENGLISH 15. OVERLOAD PROTECTION: 15
Page 14 and 15: ENGLISH Protection Description Keyp
Page 16 and 17: ENGLISH 19.2. MIW-02: External modu
Page 18 and 19: ENGLISH Soft-Starter is in fault co
Page 20 and 21: ENGLISH 20. TABLE OF PARAMETERS (FO
Page 22 and 23: ENGLISH Parameter Description / Not
Page 24 and 25: ENGLISH Parameter Description / Not
Page 26 and 27: ENGLISH Parameter P220 HMI/(Trimpot
Page 28 and 29: ENGLISH 23. APPENDIX FOR CE CONFORM
Page 30 and 31: ENGLISH WARRANTY SSW-05 Plus WEG wa
Page 32 and 33: ESPAÑOL MANUAL DE INSTALACION Y OP
Page 34 and 35: 5. DESCRIPCIÓN DEL SSW-05 PLUS: En
Page 36 and 37: ESPAÑOL 11. COMO INSTALAR Y CONECT
Page 38 and 39: ESPAÑOL 12.3. Ajuste de la Rampa d
Page 40 and 41: ESPAÑOL 14. PROTECCIONES Y SEÑALI
Page 42 and 43: ESPAÑOL 16.RESET: Una condición d
Page 44 and 45: ESPAÑOL 18. SOLUCIÓN DE PROBLEMAS
Page 46 and 47: ESPAÑOL 19.3.1. Descripción del H
Page 48 and 49: ESPAÑOL 19.3.5. Instalación del H
Page 50 and 51: ESPAÑOL 21. CÓDIGO Y DESCRIPCIÓN
Page 52 and 53: ESPAÑOL Parámetro Descripción /
Page 54 and 55: ESPAÑOL Parámetro P204 Carga par
Page 56: ESPAÑOL Parámetro P314 Tiempo de

WARRANTY SSW-05 Plus - Dimotec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?