WARRANTY SSW-05 Plus - Dimotec
WARRANTY SSW-05 Plus - Dimotec
WARRANTY SSW-05 Plus - Dimotec
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
ENGLISH<br />
Protection<br />
Description<br />
Keypad HMI<br />
Connection Fault<br />
Locked Rotor<br />
Thyristor overload<br />
Overcurrent<br />
Incorrect phase<br />
sequence<br />
Undervoltage in the<br />
Control Supply<br />
Internal<br />
By-pass relay<br />
contact is open<br />
Overcurrent before<br />
By-pass<br />
Overcurrent of the<br />
<strong>SSW</strong>-<strong>05</strong> By-pass<br />
relay<br />
Frequency out of<br />
tolerance<br />
<strong>SSW</strong>-<strong>05</strong><br />
Front Panel<br />
Available only when<br />
HMI-<strong>SSW</strong><strong>05</strong>-RS is used<br />
(see chapter 19)<br />
LED<br />
(Stall)<br />
LED<br />
(Internal Fault)<br />
flashes 6 times<br />
LED<br />
(Overcurrent)<br />
LED<br />
(Phase Seq)<br />
LED<br />
(Internal Fault)<br />
flashes 2 times<br />
LED<br />
(Internal Fault)<br />
flashes 3 times<br />
LED<br />
(Internal Fault)<br />
flashes 4 times<br />
LED<br />
(Internal Fault)<br />
flashes 5 times<br />
LED<br />
(Internal Fault)<br />
flashes 1 time<br />
Fault Display<br />
HMI-<strong>SSW</strong><strong>05</strong>-RS<br />
(see chapter 19.3)<br />
E31<br />
E63<br />
E64<br />
E66<br />
E67<br />
E70<br />
E71<br />
E72<br />
E73<br />
E75<br />
Reset<br />
Power-on<br />
This fault disappears<br />
automatically<br />
when HMI<br />
reestablishes<br />
the communication<br />
with the<br />
Soft-Starter.<br />
Power-on<br />
Reset key<br />
key<br />
Auto-reset<br />
DI2.<br />
key<br />
Auto-reset<br />
Power-on<br />
Reset key<br />
key<br />
Auto-reset<br />
DI2.<br />
Power-on<br />
Reset key<br />
key<br />
DI2.<br />
Power-on<br />
Reset key<br />
key<br />
Auto-reset<br />
DI2.<br />
Power-on<br />
Reset key<br />
key<br />
Auto-reset<br />
DI2.<br />
Power-on<br />
Reset key<br />
key<br />
Auto-reset<br />
DI2.<br />
Power-on<br />
Reset key<br />
key<br />
Auto-reset<br />
DI2.<br />
Power-on<br />
Reset key<br />
key<br />
Auto-reset<br />
DI2.<br />
Possibles Causes<br />
Keypad cable misconnected.<br />
Electrical noise in the<br />
installation (electromagnetic<br />
interference).<br />
The time programmed for the<br />
acceleration ramp is shorter than<br />
the actual acceleration time.<br />
Load on the motor shaft too high<br />
Too much successive starts.<br />
Short-circuit between phases.<br />
Motor shaft is locked.<br />
Network phase sequence<br />
inverted at the input.<br />
Electronics supply lower than the<br />
required one.<br />
<strong>SSW</strong>-<strong>05</strong> is defective.<br />
The time programmed for the<br />
acceleration ramp is shorter than<br />
the actual acceleration time.<br />
Short-circuit between phases.<br />
Motor shaft is locked.<br />
The line frequency is out of range<br />
(+/- 10%), when compared<br />
with the rated frequency (50Hz<br />
or 60Hz).<br />
Note:<br />
To prevent the E31 fault, when HMI-<strong>SSW</strong><strong>05</strong>-RS is applied, please avoid resetting the fault through the digital inputs<br />
(DI2) and through the reset key located on the <strong>SSW</strong>-<strong>05</strong> front panel.<br />
English-14
Change language