Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Sailmaker Instructions<br />
Halyard Shackle<br />
Head Shackle<br />
Feeder Entrance<br />
Tack Shackle<br />
Pivot<br />
Point<br />
Connector<br />
Foil<br />
Actual Size<br />
Echelle 1, Tatsächliche Grsse, Dimensioni Reali<br />
7 7 /16"<br />
188 mm<br />
7 1 /4"<br />
184 mm<br />
4 7 /8"<br />
124 mm<br />
1 1 /4"<br />
32 mm<br />
5 1 /4" Max<br />
133 mm<br />
3 3 /4" Min<br />
95 mm<br />
7 3 /8"<br />
187 mm<br />
9 7 /8" Max<br />
251 mm<br />
8 3 /8" Min<br />
213 mm<br />
12 1 /4" Max<br />
311 mm<br />
10 3 /4" Min<br />
273 mm<br />
9 15 /16"<br />
252 mm<br />
40 1 /2" Max<br />
1029 mm<br />
37 1 /2" Min<br />
953 mm<br />
*32" Min<br />
813 mm<br />
Luff Tape • Tack and Head Shackles • Suncover<br />
■ Sail Type<br />
The <strong>Harken</strong> furler will work with conventional sails or<br />
sails with built in shaping devices such as Aeroluff<br />
®<br />
,<br />
Pirini Luff or foam luff.<br />
■ Luff Length<br />
Note offsets above and below the sail.<br />
A shorter luff may be required if a halyard restrainer is<br />
necessary (page 30) or a toggle or link plates are used<br />
(page 8) below the furler to raise the drum.<br />
If the luff of the sail is not long enough to put the<br />
halyard swivel near the top of the headstay foil,<br />
make sure a pendant is added, see page 30.<br />
■ Tack Setback<br />
Note setback for the tack shackle and cut the sail<br />
accordingly.<br />
■ Luff Tape Size<br />
Unit 1 requires number 6 ( 6 /32" or 5 mm)<br />
luff tape.<br />
■ Luff Tape Length<br />
Cut off the top of the luff tape so it is 18 to 24" (450 to<br />
600 mm) below the head of the sail. This will allow the<br />
head to lag behind the rest of the sail to help flatten<br />
the sail. It will also help the head to roll more smoothly.<br />
Note feeder height and extend the bottom of the luff<br />
tape downwards so it is below the feeder. This will prevent<br />
the luff tape from catching in the feeder as the sail<br />
is lowered. *The 32" (813 mm) minimum pertains to<br />
shortened bottom foil installation, see page 13. Other<br />
installations will have a minimum feeder height of<br />
37 1 /2" (953 mm).<br />
■ Tack and Head Shackles<br />
Make sure tack and head<br />
shackles fit the sail rings.<br />
The minimum inside<br />
A<br />
dimensions of the standard<br />
head and tack shackles are:<br />
(A) 1 1 /16" (27 mm) and<br />
(B) 1 /2" (13 mm)<br />
■ Suncover<br />
B<br />
Suncovers may be installed on either side of the sail.<br />
However, make sure you match other sails in the customer's<br />
inventory.<br />
Clevis Pin<br />
February 2006 Unit 1 MKIII 6