UNIT 1 - Harken

Preassembly
Foil Length Instruction
■ If your pin-to-pin headstay length is one of the dimensions shown below, no special length top foil is needed.
A full length 7' (2.13 m) foil is used as the top foil.
24' 8" (7.518 m) 31' 8" (9.652 m) 38' 8" (11.786 m) 45' 8" (13.919 m)
■ You will use a recessed top connector (page 16).
■ Do not cut 24" (610 mm) bottom foil.
■ If your pin-to-pin headstay length is shown below, use a hacksaw to cut a special
length top foil from a 7' (2.13 m) foil.
24' 9" (7.543 m)
24'10" (7.569 m)
24'11" (7.595 m)
25' 0" (7.620 m)
25' 1" (7.645 m)
31' 9" (9.677 m)
31'10" (9.703 m)
31'11" (9.728 m)
32' 0" (9.754 m)
32' 1" (9.779 m)
38' 9" (11.811 m)
38'10" (11.836 m)
38'11" (11.862 m)
39' 0" (11.887 m)
39' 1" (11.913 m)
45' 9" (13.945 m)
45'10" ( 13.970 m)
45'11" (13.995 m)
46' 0" ( 14.021 m)
46' 1" ( 14.046 m)
Cut Top Foil to This Length
6 1 /2" (165 mm)
7 1 /2" (191 mm)
8 1 /2" (216 mm)
9 1 /2" (241 mm)
10 1 /2" (267 mm)
■ You will not use a recessed top connector (Page 16).
■ Shorten the bottom foil 5 1 /2" (140 mm) and drill screw
‐holes as described on P. 12.
■ If your pin-to-pin headstay length is shown below use a hacksaw to cut a special
length top foil from a 7' (2.13 m) foil.
25' 2" (7.671 m)
25' 3" (7.696 m)
25' 4" (7.722 m)
32' 2" (9.804 m)
32' 3" (9.830 m)
32' 4" (9.855 m)
39' 2" (11.938 m)
39' 3" (11.963 m)
39' 4" (11.989 m)
46' 2" (14.072 m)
46' 3" (14. 097 m)
46' 4" (14.122 m)
Cut Top Foil to This Length
6" (152 mm)
7" (178 mm)
8" (203 mm)
■ You will not use a recessed top connector (Page 16).
■ Do not cut 24" (610 mm) bottom foil.
■ If your pin-to-pin headstay length is shown below use a hacksaw to cut a special
‐length top foil from a 7' (2.13 m) foil.
25' 5" (7.747 m)
25' 6" (7. 772 m)
25' 7" (7.798 m)
25' 8" (7.823 m)
32' 5" (9.881 m)
32' 6" (9.906 m)
32' 7" (9.931 m)
32' 8" (9.957 m)
39' 5" (12.014 m)
39' 6" (12.040 m)
39' 7" (12.065 m)
39' 8" (12.090 m)
46' 5" (14.148 m)
46' 6" (14.173 m)
46' 7" (14.199 m)
46' 8" (14.224 m)
Cut Top Foil to This Length
14 1 /2" (368 mm)
15 1 /2" (394 mm)
16 1 /2" (419 mm)
17 1 /2" (445 mm)
■ You will use a recessed top connector (page 16).
■ Shorten the bottom foil 5 1 /2" (140 mm) and drill screw
‐holes as described on P. 12.
January 1999 Unit 1 MKIII 13