apparecchiatura elettronica per basculanti control board for ... - Faac
apparecchiatura elettronica per basculanti control board for ... - Faac
apparecchiatura elettronica per basculanti control board for ... - Faac
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
CONTROL BOARD FOR UP-AND-OVER DOORS<br />
INSTRUCTIONS FOR USE- DIRECTIONS FOR INSTALLATION<br />
1. GENERAL FEATURES<br />
5<br />
ENGLISH<br />
Thanks to the high-power <strong>per</strong><strong>for</strong>mance of its built-in microprocessor, this <strong>control</strong> unit <strong>for</strong> up-and-over doors offers a wide<br />
number of services and adjustments, with slowdown and motor <strong>control</strong>. It also guarantees a high active safety level through<br />
electronic power <strong>control</strong>.<br />
A sophisticated electronic <strong>control</strong> constantly monitors the power circuit and blocks the <strong>control</strong> unit if faults occur which<br />
may cause the electronic clutch to o<strong>per</strong>ate incorrectly.<br />
The main settings and o<strong>per</strong>ating modes, time and motor power adjustments can be defined using dip-switches .<br />
2. TECHNICAL SPECIFICATIONS<br />
2.1 HARDWARE SPECIFICATIONS<br />
Power supply<br />
230VAC - 50Hz<br />
Max. absorbed power<br />
12VA<br />
Motors max. load<br />
800W<br />
Power supply <strong>for</strong> accessories<br />
24Vdc<br />
Accessories max. load<br />
300mA<br />
O<strong>per</strong>ating ambient tem<strong>per</strong>ature - 20°C + 55°C<br />
Protection fuses<br />
mains circuit / accessories<br />
Rapid connector<br />
<strong>for</strong> decoding cards or 5-Pin RP receivers<br />
Terminal <strong>board</strong>s<br />
pull-out<br />
Terminal <strong>board</strong> inputs Open / Stop / Closing safety devices / Opening safety devices /<br />
Opening limit-switch / Closing limit-switch<br />
Terminal <strong>board</strong> outputs flashing lamp 230VAC - 40W /motor /<br />
outside courtesy lamp 230VAC - 25W /<br />
24 Vdc accessories power supply<br />
Max. load of built-in courtesy lamp<br />
25W<br />
Max. load of outside courtesy lamp<br />
25W<br />
2.2 OPERATING PARAMETERS<br />
Logic<br />
automatic/semi-automatic<br />
Pause time<br />
Max torque at thrust<br />
programmable from 0 to 60 sec.<br />
fixed 0.5 sec.<br />
O<strong>per</strong>ating time<br />
Fail safe<br />
programmable from 17 to 30 sec.<br />
Yes/No<br />
<br />
<br />
Pre-flashing<br />
Yes ( 5 sec.) / No<br />
<br />
Electronic clutch<br />
programmable on 8 levels<br />
Limit-switch tripping modes 4 types of o<strong>per</strong>ation<br />
Courtesy timer<br />
fixed 60 sec.<br />
3. LAY OUT OF CONTROL BOARD (fig.1)<br />
F1 Fuse F1 5x20 5A/250V (mains circuit)<br />
F2 Fuse F2 5x20 500mA/250V (accessories)<br />
TF1 Trans<strong>for</strong>mer<br />
LP1 Courtesy lamp 25W 230V E14<br />
LD1 Power-supply Led<br />
J1 230VAC power supply input terminal <strong>board</strong><br />
J2<br />
J3 Low voltage input/accessories terminal <strong>board</strong><br />
J4 Rapid connector <strong>for</strong> decoding cards / 5-Pin RP receivers<br />
DS1 Programming microswitches<br />
Motor output terminal <strong>board</strong>, flashing lamp and outside courtesy lamp<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
Fig. 1
Change language