CE Source Four jr & CE Source Four jr Zoom - SXS Events

More documents

Recommendations

Info

EnglishCaution! Improperly installed lamps cause premature lampand Phone: courtesy Audio-Visual failure and socket 0870 problems. of 080 Services 23426. Press lamp retainers down across lamp base and clip securely.7. To reinstall the lamp housing, line up the side fins and the boltmail:hole,www.sxsevents.co.ukenquiries@sxsevents.co.ukthen tighten the knurled bolt to secure the housing.Aligning the lampUse the two concentric knobs on the rear of the lamp housing toalign the lamp. The outer knob centres the lamp within thereflector and locks it in position; the inner knob fine tunes thefield. See Figure 4.Lamp housingKnurled boltImportant: Luminaire must be on to align the lamp.1. Unlock the outer knob by turning it anticlockwise one turn.2. Gently push the outer knob from side to side and up and downuntil the lamp is centred in the field.3. Once the lamp is centred, tighten the outer knob to lock it inplace.4. Turn the inner knob right or left to adjust for optimum flat field.Focusing the beamOn a fixed field angle CE Source Four jr, with a 26°, 36° or 50°lens, adjust the lens position to focus the edge of the beam. On aCE Source Four jr Zoom, adjust the position of both lenses to setthe beam's spread and to focus the edge of the beam. The Zoomlenses give you a range from 25° to 50°.Centreadjustment(outer knob)Peak and flatadjustment(inner knob)Figure 41. Loosen the beam focus knob(s) on the underside of the barrel.See Figure 5.2. Slide the lens(es) forward or backward to achieve the desiredbeam edge.3. Once the luminaire is focused, tighten the beam focusknob(s).Beam focus knobColour frameFigure 5Gel notesFor best results, always use a high quality, high temperaturecolour medium. ETC does not guarantee performance with lowtemperature, saturated colour gels.www.sxsevents.co.uk8 • CE Source Four jr & CE Source Four jr Zoom
and Phone: courtesy Audio-Visual 0870 of 080 Services 2342Shaping the beamEnglishYou may shape the beam with the shutters, a pattern, or an optionalmail: www.sxsevents.co.ukenquiries@sxsevents.co.ukdrop-in iris (ETC part #7062A1011).Pattern holder slotPattern projectionThe pattern holder slot is on the top side of the barrel, immediately infront of the shutters. It accommodates the M-size pattern holdershown in Figure 7. The M-size pattern holder’s handle should bendaway from the shutter handle at a 30° angle. If your pattern holder’shandle is straight, you may bend it far enough to not interfere with theaction of the shutter handle.Use an optional donut (ETC part #7060A1037) in the accessory holderto enhance pattern projection.Drop-in iris slotThe drop-in iris slot is on the top side of the front barrel, immediately infront of the pattern holder slot. See Figure 6. When it is not in use, asmall sheet metal cover secured with two crosshead screws preventslight leakage and retains the iris assembly. To install an iris, followthese steps.Caution!Be certain the luminaire is not hot before installing theiris.1. Use a crosshead screwdriver to loosen the screws on the drop-iniris slot cover. Do not remove the screws.2. Slide the cover completely forward, exposing the slot.3. Insert the iris. The flat side must be toward the shutters and the irishandle should extend out of slot.4. Slide the slot cover back toward the shutters until it meets the irishandle. Leave enough space to move the iris handle. Tighten thescrews.Drop-iniris slotFigure 6M-size pattern holder(ETC part # 7062A1010)Figure 7Iris(ETC part # 7062A1011)Figure 8www.sxsevents.co.ukCE Source Four jr & CE Source Four jr Zoom • 9
Page 1 and 2: vent courtesy production Phone: of
Page 3: vent courtesy production Phone: of
Page 8 and 9: EnglishWiring and power information
Page 12 and 13: EnglishSwitching lens assembliesand
Page 14 and 15: EnglishFollow the steps below to gr
Page 16 and 17: DeutschHinweise für den Anschluß
Page 18 and 19: Deutsch4. Richten Sie die flachen S
Page 20 and 21: DeutschLinsenhalter austauschenand
Page 22 and 23: Deutschand Phone: courtesy Audio-Vi
Page 24 and 25: FrançaisCâblage électriqueand co
Page 26 and 27: Françaisand Phone: courtesy Audio-
Page 28 and 29: FrançaisChangement des montages de
Page 30 and 31: Françaisand Phone: courtesy Audio-
Page 32 and 33: EspañolConexionado a la redand Pho
Page 34 and 35: Españoland Phone: courtesy Audio-V
Page 36 and 37: EspañolPara cambiar el ensamblaje
Page 38 and 39: Españoland Phone: courtesy Audio-V
Page 40: vent courtesy production Phone: of

CE Source Four jr & CE Source Four jr Zoom - SXS Events

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?