Manuale GATE 2 DG Rev.02 ITA (testo nero) - SEA (UK)

More documents

Recommendations

Info

®Sistemi Elettronicidi Apertura Porte e CancelliInternational registered trademark n. 804888EnglishMOTORS CONNECTION, CAPACITYAND POWER SUPPLYCN3GATE 2 DGCN41 2 3 4 5 1 2 3 4 5CN4CN3Phase 1NeutralPhase 2Phase 1NeutralPhase 2Cap M145Cap M245Motor 1Motor 2 connectionM1M = Opening /ClosingCom = COMMONExample1CN6231Motor 2Motor 1 connectionM = Opening/ClosingM21 2 3LineNeutralCom = COMMONExample23POWER SUPPLY INPUTNOTE: For power supply connection follow the rules inforce134067411385Rev.02 - 09/2012
®Sistemi Elettronicidi Apertura Porte e CancelliInternational registered trademark n. 804888EnglishGATE 2 DGLIMIT SWITCH, ELECTROLOCK CONNECTIONLimit switchDoes not need a jumper when not connected.For the limit switch function, limit switches must be installed, both inopening and closing. In the case of a single leaf it is not necessary tobridge the limit switches of motor 2.Anti-intrusion function can be activated. This function needs at leastone limit switch, which pushes the motor in closing direction once it’sreleased.!The right operation of the limit switch is guaranteed whenthe motors turning direction correspond with the respectiveemployed limit switche.Com = CommonN.C.C= ContactLimit switchM1 openingN.C.Limit switchM1 closingLimit switchM2 openingLimit switchM2 closingN.C.N.C.51525354CN21 2 3 4 5 6 7 8 9 109 10ELECTROLOCKElectrolock outputA 12V 15W max electrolock can be connectedElectrolock can be deactivated when not used for energy saving onthe control unit. Electrolock release can be timed from 0 to 5 s.The electrobrake can be set: only before opening, only beforeclosing or in both directions.Signals Kind of alarm SolutionsFAULMotors current faultSure there are no short circuits on the motor or on the control unit.FT.2424V Power supply fault Make sure there are no short circuits on the wiring or on the control unit andno overloads.FT.AU24VA output voltageMake sure there are no short circuits on wiring or control unit andno overload.FT.LIF.EDGF.PHOFT.fFT.FLY LPower supply faultBalanced edge input faultSelf-test photocells faultLimit switch activation faultFlashing lamp faultMax. cyclesALARM DESCRIPTIONCheck the network or the F2 fuseCheck for a 8.2 Ohms resistive value on the edge input, if not availableenter it, or disable the reading of the 8k2 in the special menu.Check the photocells operation and / or connections on the control unit.Check the operation of both limit switches and / or correspondencebetween movement direction of the motor and engaged limit switches.Check connections and / or conditions of the lamp.Maintain and / or reset the number of performed cycles.Note: To exit from the error messages, press OK. If the error persists, make all required checks for the specific error and / or disconnect thedevice that generates the error to see if the error disappears.At each opening and closing of the automation the flashing light will blink. It blinks once per second during opening and twice per secondduring closing, while it remains lit during pause.It is possible to view the alarms also on the flashing light or on the control lamp, simply by observing the number of flashes emitted andverifying the reference in the table below:Blinks92364Cause of alarmMotors faultPhotocell in closingPhotocell in openingCollision in openingSafety edgeBlinks5764 fastCause of alarmStopMax. Cycles reachedCollision in closingLimit switch fault67411385Rev.02 - 09/2012 41
Page 1 and 2: ®Sistemi Elettronicidi Apertura Po
Page 5 and 6: Sistemi Elettronicidi Apertura Port
Page 13 and 14: DOWNUPSistemi Elettronicidi Apertur
Page 31 and 32: DOWNS.StrY lN. Yt rUPk.iPk.224uaUP
Page 33 and 34: DOWNUP®Sistemi Elettronicidi Apert
Page 39: ®Sistemi Elettronicidi Apertura Po
Page 83 and 84: CONDIZIONI DI VENDITAEFFICACIA DELL
Page 87 and 88: Questo articolo è stato prodotto s

Manuale GATE 2 DG Rev.02 ITA (testo nero) - SEA (UK)

Create successful ePaper yourself

Delete template?

Save as template?