Biuletenis 2013-01 AS - LST - Standartizacijos departamentas prie AM

LIETUVOS STANDARTIZACIJOS DEPARTAMENTO BIULETENIS 2013 Nr. 1ISO/TC 85/SC 5 ISO 16424:2012Nuclear energy - Evaluation of homogeneity of Gddistribution within gadolinium fuel blends anddetermination of Gd2O3 content in gadolinium fuel pelletsby measurements of uranium and gadolinium elementsISO/TC 87 ISO 17727:2012Cork-Cork stoppers for still wine - Sampling plan forthe quality control of cork stoppersISO/TC 92/SC 1 ISO/TS 5660-3:2012Reaction-to-fire tests - Heat release, smoke productionand mass loss rate - Part 3: Guidance on measurementISO/TC 92/SC 3 ISO 29903:2012Guidance for comparison of toxic gas data betweendifferent physical fire models and scalesISO/TC 92/SC 4 ISO 16737:2012Fire safety engineering - Requirements governingalgebraic equations - Vent flowsISO/TC 94/SC 3 ISO/TR 18690:2012Guidance for the selection, use and maintenance ofsafety and occupational footwear and other personalprotective equipment offering foot and leg protectionISO/TC 96/SC 10 ISO 8686-1:2012Cranes - Design principles for loads and loadcombinations - Part 1: GeneralISO/TC 104/SC 4 ISO 6346:1995/Amd 3:2012Freight containers - Coding, identification and marking- Amendment 3ISO/TC 108/SC 4 ISO 10068:2012Mechanical vibration and shock - Mechanicalimpedance of the human hand-arm system at thedriving pointISO/TC 118/SC 3 ISO 11148-3:2012Hand-held non-electric power tools - Safetyrequirements - Part 3: Drills and tappersISO/TC 118/SC 3 ISO 11148-4:2012Hand-held non-electric power tools - Safetyrequirements - Part 4: Non-rotary percussive powertoolsISO/TC 118/SC 3 ISO 11148-6:2012Hand-held non-electric power tools - Safetyrequirements - Part 6: Assembly power tools forthreaded fastenersISO/TC 118/SC 3 ISO 11148-12:2012Hand-held non-electric power tools - Safetyrequirements - Part 12: Circular, oscillating andreciprocating sawsISO/TC 121/SC 3 IEC 60601-1-8:2006/Amd 1:2012Medical electrical equipment - Part 1-8: Generalrequirements for basic safety and essentialperformance - Collateral standard: Generalrequirements, tests and guidance for alarm systemsin medical electrical equipment and medical electricalsystems - Amendment 1ISO/TC 123/SC 5 ISO 3548-3:2012Plain bearings - Thin-walled half bearings with orwithout flange - Part 3: Measurement of peripherallengthISO/TC 126 ISO 16055:2012Tobacco and tobacco products - Monitor test piece -Requirements and useISO/TC 130 ISO 12647-6:2012Graphic technology - Process control for theproduction of half-tone colour separations, proofs andproduction prints - Part 6: Flexographic printingISO/TC 131/SC 4 ISO 6162-1:2012Hydraulic fluid power - Flange connections with splitor one-piece flange clamps and metric or inch screws- Part 1: Flange connectors, ports and mountingsurfaces for use at pressures of 3,5 MPa (35 bar) to35 MPa (350 bar), DN 13 to DN 127ISO/TC 131/SC 4 ISO 6162-2:2012Hydraulic fluid power - Flange connections with splitor one-piece flange clamps and metric or inch screws- Part 2: Flange connectors, ports and mountingsurfaces for use at a pressure of 42 MPa (420 bar),DN 13 to DN 76ISO/TC 131/SC 8 ISO 10770-2:2012Hydraulic fluid power - Electrically modulatedhydraulic control valves - Part 2: Test methods forthree-port directional flow-control valvesISO/TC 135/SC 2 ISO 3059:2012Non-destructive testing - Penetrant testing andmagnetic particle testing - Viewing conditionsISO/TC 138/SC 1 ISO 15398:2012Specifications for thermoplastics covers and framesfor manholes and inspection chambers used innon-traffic areasISO/TC 138/SC 4 ISO 18225:2012Plastics piping systems - Multilayer piping systemsfor outdoor gas installations - Specifications for systemsISO/TC 146/SC 2 ISO 14382:2012Workplace atmospheres - Determination of toluenediisocyanate vapours using 1-(2-pyridyl)piperazinecoatedglass fibre filters and analysis by highperformance liquid chromatography with ultravioletand fluorescence detectorsISO/TC 150 ISO 14630:2012Non-active surgical implants - General requirementsISO/TC 150/SC 2 ISO 25539-2:2012Cardiovascular implants - Endovascular devices -Part 2: Vascular stentsISO/TC 156 ISO 7539-1:2012Corrosion of metals and alloys - Stress corrosiontesting - Part 1: General guidance on testingproceduresISO/TC 156 ISO 13174:2012Cathodic protection of harbour installationsISO/TC 156 ISO 13573:2012Corrosion of metals and alloys - Test method forthermal-cycling exposure testing under hightemperaturecorrosion conditions for metallic materialsISO/TC 156 ISO 26146:2012Corrosion of metals and alloys - Method formetallographic examination of samples after exposureto high-temperature corrosive environmentsISO/TC 163/SC 1 ISO 12569:2012Thermal performance of buildings and materials -Determination of specific airflow rate in buildings -Tracer gas dilution methodISO/TC 163/SC 2 ISO 13788:2012Hygrothermal performance of building componentsand building elements - Internal surface temperatureto avoid critical surface humidity and interstitialcondensation - Calculation methodsISO/TC 164/SC 1 ISO 9513:2012Metallic materials - Calibration of extensometer systemsused in uniaxial testingISO/TC 172/SC 6 ISO 17123-5:2012Optics and optical instruments - Field procedures fortesting geodetic and surveying instruments - Part 5:Total stationsISO/TC 172/SC 7 ISO 10341:2012Ophthalmic instruments - Refractor headsISO/TC 172/SC 7 ISO 11979-3:2012Ophthalmic implants - Intraocular lenses - Part 3:Mechanical properties and test methodsISO/TC 172/SC 7 ISO 11980:2012Ophthalmic optics - Contact lenses and contact lenscare products - Guidance for clinical investigations23