Manual _ 0601-10.1.pdf - Firma Servotool GmbH

More documents

Recommendations

Info

BAND SAW THE NUMBERS IN THE FOLLOWING TEXT CORRESPOND WITH THE PICTURES AT PAGE 2 SAFETY AND OPERATING INSTRUCTIONS For your own safety and for the safety of others, please read these instructions carefully before using this appliance. It will help you understand your product more easily and avoid unnecessary risks. Keep this instruction manual in a safe place for future use. CONTENTS 1. Machine data 2. Safety instructions 3. Installation 4. Operation 5. Maintenance 1. MACHINE DATA TECHNICAL SPECIFICATION Voltage | 230 V~ Frequency | 50 Hz Power input | 350 W No load speed Max. saw capacity 90 | 1300/min o | 85 mm Max. saw capacity 45 o PRODUCT INFORMATION Fig. 1 1. Base 2. On/off switch 3. Saw blade 4. Saw blade guard 5. Blade guide adjusting knob 6. Frame 7. Blade tension knob 8. Adjustment knob 9. Sawdust outlet 10. Blade guides 11. Table 12. Table tilt groove 13. Graduated scale 14. Pointer 15. Table locking knob | 42 mm Table dimensions | 300x300mm Lpa (sound pressure) | 76,8 dB(A) Lwa (acoustic power) | 87,56 dB(A) Vibration | 5,0 m/s 2 2. SAFETY INSTRUCTIONS The following symbols are used in these instructions for use: Read instructions carefully In accordance with essential applicable safety standards of European directives Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual. Indicates electrical shock hazard. Immediately unplug the plug from the mains electricity in the case that the cord gets damaged and during maintenance Keep bystanders away Wear ear and eye protection Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations. ELECTRICAL SAFETY When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions. Always check that the power supply corresponds to the voltage on the rating plate. Replacing cables or plugs Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet. Using extension cables Only use an approved extension cable suitable for the power input of the machine. The minimum conductor size is 1.5 mm 2 . When using a cable reel always unwind the reel completely. BEFORE USING THE MACHINE: • Make sure: • The voltage of the machine corresponds to the mains voltage. • To use an earthed power source (wall socket). • The cord and the plug are in good condition, i.e. not frayed or damaged. • No saw teeth are missing and the blade is not cracked or split. Otherwise replace immediately. 4 Ferm Ferm 65
64 Ferm • The blade is properly tensioned and aligned. • The base of the band saw machine must be placed on or secured to a solid and level surface or bench. • Never apply sideward pressure on the blade as this may cause the blade to break. • Be careful when cutting wood with knots, nails or cracks in it and/or dirt on it, as these can cause the blade to get stuck. • Never leave the band saw machine unattended. • The teeth of the blade must point downwards. WHEN USING THE MACHINE: • Clamp the workpiece to the saw table. Support the workpiece to prevent it from breaking, making sure your hand is behind the blade and moves away from it. The arm that holds down the work must not cross the arm that operates the band saw machine. • Never remove wood chips and suchlike that are close to the blade with your hands. When wood chips get stuck between fixed and/or moving parts, stop the band saw machine before removing them. • When cutting small pieces of wood use a pusher block to feed the wood along the blade. • The saw blade is one of the most important components of your band saw machine. Selecting the right material, teeth, as well as correct fitting of the blade not only prolongs the life of the blade, but also prevents it from breaking and cracking with all its consequences. • Be careful when cutting scrap wood. As the quality of the cut is not important, the user tends to be less concentrated, not to check the wood for nails, knots or other irregularities, and to put undue pressure on the blade. • Never use long extension cables. • Do not use saw bands which are damaged or deformed. • Replace table insert when worn. • When cutting round timber use a suitable device to prevent twisting of the workpiece. • When bevel cutting with the table inclined, place the guide on the lower part of the table. • Connect band saws to a dust collecting device when operating. • Do not operate the machine when the door or guard protecting the band is not closed. • Adjust the guard as close as possible to the piece to be cut. • Take care that the selection of the band saw and the speed depend on the material to be cut. SWITCH OFF IMMEDIATELY IF: • The band saw machine becomes overheated. • The cord and/or plug are defective or damaged. • The switch is defective. • Insulation material starts to smell or burn. 3. INSTALLATION MOUNTING THE BASE PLATE • Make sure that the protruding parts of the base plate are fastened to the side of the motor. • Fasten the base plate to the bottom of the machine with 4 bolts. MOUNTING THE BAND SAW MACHINE The band saw machine has to be mounted on a permanent location. The band saw machine has to be secured to a flat surface, such as a bench. • Position the band saw machine. • Mark the four holes with a pen or pencil. • Remove the band saw machine and drill four holes with a diameter of 10 mm where marked. • Reposition the band saw machine and from the top insert the M10 bolts provided. Fit the washers and tighten the nuts underneath. MOUNTING AND ALIGNING THE BAND SAW TABLE Fig. 2-4 Disconnect the machine from the power supply. • Remove the bolt and butterfly nut from the table (A) to remove the table. • Put table (A) on the band saw frame (B) (see Fig. 2), making sure the mounting rib (C) on the frame fits into the groove in the table. • Lock the table in horizontal position by means of the table locking knob (A) (see Fig. 3).Tighten the table locking knob by means of the Allen key, moving the grip of the knob backwards to prevent it from turning. When the table is almost locked, use the grip to secure tightly.) • Retighten the bolt and butterfly nut. • Use a small square (A) to check the position of the table (see Fig. 4). If the table is not properly locked proceed as follows: • Loosen the locking nut by means of an open-ended spanner. • Completely loosen bolt (C) in the frame by means of the Allen key provided. Slightly loosen knob (B) (see Fig. 4) and move the table, making sure it is at right angles to the side of the bench. • Retighten knob (B). • Retighten bolt (C) until it touches the frame of the band saw machine (i.e. clockwise). • Retighten the locking nut. • Set the graduated scale at 00 (see Fig. 4). • Check that the table is at an angle of 45° when the graduated scale indicates 45°. • If not, repeat the above steps. • Mount the fence and insert the pointer into the groove in the table. BLADE TENSIONING • Install blade. • Turn tension lever clockwise until spring begins to compress. • To set proper tension turn lever 2 additional turns. Ferm 5
Page 1 and 2: UK Subject to change D Änderungen
Page 3: SPARE PARTS LIST REF NR DESCRIPTION
Page 7 and 8: VEDLIGEHOLDELSE Træk altid stikket
Page 9 and 10: • Anbring herefter længdeføring
Page 11 and 12: 2. SIKKERHEDSINSTRUKTIONER Der brug
Page 13 and 14: 7. Båndsagen kutter ikke snitt på
Page 15 and 16: 3. INSTALLERING MONTERE BASISPLATEN
Page 17 and 18: BÅNDSAG TALLENE I FØLGENDE TEKST
Page 19 and 20: 4. KÄYTTÖ • Vannesaha sahaa jat
Page 21 and 22: • tarkista terän kireys ja suunt
Page 23 and 24: 5. UNDERHÅLL Vid underhåll och re
Page 25 and 26: ATT SPÄNNA BANDSÅGBLADET • Mont
Page 27 and 28: BANDSÅG SIFFRORNA I NEDANSTÅENDE
Page 29 and 30: 2. Il nastro della sega non si muov
Page 31 and 32: portato a tagliare senza fare atten
Page 33 and 34: CEı DÉCLARAÇÀO DE CONFORMIDADE

Manual _ 0601-10.1.pdf - Firma Servotool GmbH

Create successful ePaper yourself

Delete template?

Save as template?