14:53 - AEG Haustechnik
14:53 - AEG Haustechnik
14:53 - AEG Haustechnik
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
Button LCD Button Note<br />
P<br />
Only for<br />
Powertherm<br />
charging<br />
model<br />
M<br />
AF M<br />
-20, 8<br />
P<br />
P<br />
<strong>14</strong>:<strong>53</strong> <strong>14</strong>:<strong>53</strong><br />
1.6 Controller self-test<br />
VR LF LZ KU<br />
°C<br />
ED<br />
SH<br />
SYN<br />
VR LF LZ KU<br />
+ or –<br />
For the Fitter<br />
Display of the average outside temperature used for calculating<br />
the charge.<br />
The currently measured outside temperature value is entered in<br />
the memory by holding down the + and – buttons<br />
simultaneously for longer than 3 seconds.<br />
Stored main release time<br />
Stored additional-release time<br />
The ELFAMATIC µC 3000 must be de-energised before the self-test can be started. Then press<br />
the + and – buttons simultaneously and switch the power supply back on at the same time.<br />
8888 XXXX<br />
88:88 88:88 , ,<br />
VR LF LZ KU<br />
ED<br />
SH<br />
SYN<br />
Display segment test Software version<br />
Button LCD Button Bemerkung<br />
M<br />
M<br />
M<br />
C<br />
%<br />
EEP<br />
00<br />
TAST<br />
E/A<br />
1A<br />
TEMP<br />
-2<strong>14</strong> ,<br />
Outside temperature<br />
LF<br />
--:-- --:--<br />
LZ<br />
--:-- --:--<br />
M<br />
ED<br />
SH<br />
SYN<br />
VR LF LZ KU<br />
ED<br />
SH<br />
SYN<br />
VR LF LZ KU<br />
ED<br />
SH<br />
SYN<br />
VR LF LZ KU<br />
ED<br />
SH<br />
SYN<br />
VR LF LZ KU<br />
°C<br />
ED<br />
SH<br />
SYN<br />
VR LF LZ KU<br />
+ or –<br />
2x<br />
ED<br />
SH<br />
SYN<br />
VR LF LZ KU<br />
P<br />
M<br />
ED<br />
SH<br />
SYN<br />
VR LF LZ KU<br />
ED<br />
SH<br />
SYN<br />
M<br />
EEProm memory version<br />
VERS<br />
100 ,<br />
VR LF LZ KU<br />
ED<br />
SH<br />
SYN<br />
Button test – An internal device test is performed to check<br />
that the buttons are functioning correctly.<br />
Press the P button. The buttons + , – and M were<br />
already pressed during the self-test and therefore do not need<br />
to be tested again.<br />
Output test – The relay and Triac can be activated alternately<br />
by pressing the buttons + and – .<br />
End – If no button is pressed for 2 seconds, the display returns<br />
to the standard mode.<br />
29<br />
English