Comfort 211 accu / solar - Marantec

More documents

Recommendations

Info

8. Initial operation 8.5 Express programming 8.5.1 General notes on express programming Attention! When programming the end positions the mechanical end position must not be touched because otherwise the fuse in the charge regulator will be activated. For proper initial operation of the operator, three basic operator functions must be set using express programming: - End position DOOR OPEN - End position DOOR CLOSED - Remote control programming This programming procedure is carried out consecutively and is compulsory. Following express programming and a test run of the OPEN and CLOSED functions, the operator system is ready for use. Advice: Additional operator functions can be set using the expanded operator functions. Important factory default settings can be changed there. This programming may only be carried out by specialist personnel. 8.5.2 Programming buttons 8.5.2 / 1 The P programming button is pressed using the enclosed programming pin (A). The programming is carried out using the plus (+), minus (-) und P buttons. If no buttons are pressed within 120 seconds while in programming mode, the control unit reverts back to operating mode. A corresponding message appears in the display. Reference: The messages are explained in Chapter 10. Legend: LED off LED flashes LED flashes slowly LED pulses LED flashes quickly Factory default setting Not possible – 34 Manual for installation and operation, Comfort 211 accu / solar GB (#73385) i A
8. Initial operation 8.5.3 Express programming sequence Operating mode 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 1x >2s
Page 1 and 2: Comfort 211 accu / solar Operator S
Page 3 and 4: 2. Table of Contents 1. Meaning of
Page 5 and 6: 3. General safety advice Please rea
Page 7 and 8: 4. Product overview 4.1 Comfort 211
Page 9 and 10: 4. Product overview Version “sola
Page 11 and 12: 6. Installation 6.1 Preparation of
Page 13 and 14: 6. Installation 6.2 Installation of
Page 15 and 16: 6. Installation 6.3 / 5 Caution! In
Page 17 and 18: 6. Installation • Close the door.
Page 19 and 20: 6. Installation 6.6 Release Attenti
Page 21 and 22: 6. Installation 6.8 Mounting of the
Page 23 and 24: 6. Installation 6.8 / 6 o • Align
Page 25 and 26: 6. Installation 6.8 / 8 E • Open
Page 27 and 28: 6. Installation 6.10 Accumulator un
Page 29 and 30: 7. Hand transmitter 7.1 Operation a
Page 31 and 32: 7. Hand transmitter 7.2.2 Change co
Page 33: 8. Initial operation 8.3 Overview o
Page 37 and 38: 8. Initial operation 8.6.2 Check of
Page 39 and 40: 9. Extended operator functions 9.2
Page 41 and 42: 9. Extended operator functions 9.3.
Page 43 and 44: 9. Extended operator functions 1 2
Page 45 and 46: 9. Extended operator functions 1 2
Page 47 and 48: 10. Messages 10.2 Message numbers o
Page 49 and 50: 10. Messages 10.3.2 Malfunctions wi
Page 51 and 52: 11. Attachment Circuit diagram lege
Page 53 and 54: 11. Attachment Replacement parts le
Page 55 and 56: 11. Attachment Replacement parts le
Page 57 and 58: 11. Attachment 11.4 Manufacturer’
Page 59 and 60: Manual for installation and operati

Comfort 211 accu / solar - Marantec

Create successful ePaper yourself

Delete template?

Save as template?