TM 11-6625-2837-14&P-7 TECHNICAL MANUAL OPERATOR'S ...

More documents

Recommendations

Info

Section 1 TM 11-6625-2837-14&P-7 100 kHz - 50 ohms 100 kHz - 600 ohms C1, C4 0.015 μF Mylar 0160-0194 C1, C4 1300 pF 0160-2221 C2 0.027 μF Mylar 0170-0066 C2 3000 pF 0160-2229 C3 0.022 μF Mylar 0160-0162 C3 1100 pF 0160-2219 L1, L2 100 μH 9140-0210 L1, L2 1200 μH 9100-1655 1 MHz -50 ohms 1 MHz - 600 ohms C1, C4 1500 pF 0160-2222 C1, C4 130 pF 0140-0195 C2 3300 pF 0160-2230 C2 300 pF 0160-2207 C3 1600 pF 0160-2223 C3 120, μH 0140-0194 L1, L2 10H ±10% 9140-0114 L1, L2 120 μ 9100-1637 5 MHz - 50 ohms 10 MHz - 50 ohms C1, C2, C4 300 pF 0160-2207 C1, C4 150 pF 0140-0196 C3 680 pF 0160-3537 C2 330 pF 0160-2208 L1, L2 2 μH 9100-3345 C3 160 pH 0160-2206 L1, L2 1 μH±10% 9140-0096 NOTE Unless otherwise noted, tolerance of components is + 5% and capacitors are mica. Part numbers are Hewlett-Packard Figure 1-4. Low Pass Filters 1-12
Section 2 TM 11-6625-2837-14&P-7 2-1. INTRODUCTION 2-2. This section provides information relative to initial inspection, preparation for use, and storage and shipment of the Model 86602B RF Section plug-in. Initial Inspection provides instructions to be followed when an instrument is received in a damaged condition. Preparation For Use gives all necessary interconnection and installation instructions. Storage and Shipment provides instructions and environmental limitations pertaining to instrument storage. Also provided are packing and packaging instructions which should be followed in preparing the instrument for shipment. 2-3. INITIAL INSPECTION 2-4. Inspect the shipping container for damage. If the shipping container or cushioning material is damaged, it should be kept until the contents of the shipment have been checked for completeness and the instrument has been checked mechanically and electrically. The contents of the shipment should be as shown in Figure 1-1, and procedures for checking electrical performance are given in Section IV. If the contents are incomplete, if there is mechanical damage or defect, or if the instrument does not pass the electrical performance test, notify the nearest Hewlett-Packard office. If the shipping container is damaged, or the cushioning material shows signs of stress, notify the carrier as well as the Hewlett- Packard office. Keep the shipping materials for carrier’s inspection. The HP office will arrange for repair or replacement without waiting for claim settlement. 2-5. PREPARATION FOR USE 2-6. Power Requirements 2-7. All power required for operation of the RF Section is furnished by the mainframe. This RF Section requires approximately 40 volt-amperes. 2-8. Interconnections 2-9. Prior to installing the RF Section plug-in into the mainframe, verify that the Frequency Extension Module plug-in and interconnecting cable assemblies have been installed in accordance with the instructions contained in the Frequency Extension Module manual. SECTION II INSTALLATION 2-1 2-10. Modifications 2-11. A power supply modification to older versions of Model 8660A and 8660B mainframes are required if they are to be used with the option 002 RF Section. Damage to the synthesized signal generator system may result if an option 002 RF Section is used with an older 8660A or 8660B mainframe. 2-12. Due to the increased power consumption of the option 002 instrument, mainframes with serial prefixes 1349A and below must be modified by installing a Field Update Kit. For mainframe configurations other than option 003 (60 Hz line operation), order kit number 08660-60273. For option 003 mainframes (50 - 400 Hz line operation) order kit number 08660-60274. NOTE Verify that a new higher current fuse, HP Part Number 2110-0365, 4A Slow Blow, is used in mainframes with the power supply modification. 2-13. Operating Environment 2-14. The RF Section is designed to operate within the following environmental conditions: Temperature ........................................ 0° to +55°C Humidity ..................................... less than 95% relative Altitude ....................................... less than 15,000 feet 2-15. Installation Instructions WARNING The multi-pin plug connector which provides interconnection from mainframe to RF Section, will be exposed with the RF Section removed from the right-hand mainframe cavity. With the Line (Mains) Voltage off and power cord disconnected, power supply voltages may still remain which, if contacted, may constitute a shock hazard.
Page 1: TECHNICAL MANUAL OPERATOR’S, ORGA
Page 4 and 5: TM 11-6625-2837-14&P-7 This manual
Page 6 and 7: Section Page VII MANUAL CHANGES ...
Page 8 and 9: 0-1. Scope SECTION 0 INTRODUCTION T
Page 10 and 11: Section 1 TM 11-6625-2837-14&P-7 Fi
Page 12 and 13: Section 1 TM 11-6625-2837-14&P-7 FR
Page 14 and 15: Section 1 TM 11-6625-2837-14&P-7 FR
Page 16 and 17: Section 1 TM 11-6625-2837-14&P-7 an
Page 18 and 19: Section 1 TM 11-6625-2837-14&P-7 Ta
Page 20 and 21: Section 1 TM 11-6625-2837-14&P-7 Ta
Page 24 and 25: Section 1 TM 11-6625-2837-14&P-7 2-
Page 26 and 27: Section 3 TM 11-6625-2837-14&P-7 1
Page 28 and 29: Section 3 TM 11-6625-2837-14&P-7 1.
Page 30 and 31: Section 3 TM 11-6625-2837-14&P-7 TU
Page 44 and 45: Section 4 TM 11-6625-2837-14&P-7 PE
Page 72 and 73:
Section 4 TM 11-6625-2837-14&P-7 4-
Page 74 and 75:
Section 4 TM 11-6625-2837-14&P-7 4-
Page 76 and 77:
Section 4 TM 11-6625-2837-14&P-7 4-
Page 78 and 79:
Section 4 TM 11-6625-2837-14&P-7 PE
Page 80 and 81:
Section 4 TM 11-6625-2837-14&P-7 4-
Page 82 and 83:
Section 4 TM 11-6625-2837-14&P-7 4-
Page 84 and 85:
Section 4 TM 11-6625-2837-14&P-7 4-
Page 86 and 87:
Section 5 TM 11-6625-2837-14&P-7 an
Page 88 and 89:
Section 5 TM 11-6625-2837-14&P-7 5-
Page 90 and 91:
Section 5 TM 11-6625-2837-14&P-7 AD
Page 92 and 93:
Section 5 TM 11-6625-2837-14&P-7 AD
Page 94 and 95:
Section 5 ADJUSTMENTS 5-28A. PHASE
Page 96 and 97:
ADJUSTMENTS 5-28B. PHASE MODULATION
Page 98 and 99:
Section 6 6-1. INTRODUCTION 6-2. Th
Page 100 and 101:
Section 6 Table 6-1. Reference Desi
Page 102 and 103:
Section 6 Reference Designation HP
Page 104 and 105:
Page 106 and 107:
TM 11-6625-2837-14 & P-7 Section 6
Page 108 and 109:
Page 110 and 111:
TABLE 6-4 (continued) PART NUMBER
Page 112 and 113:
Section 7 7-1. INTRODUCTION 7-2. Th
Page 114 and 115:
Section 7 TM 11-6625-2837-14 & P-7
Page 116 and 117:
CHANGE B (Cont’d) 15. Adjust A16R
Page 118 and 119:
Section 7 TM 11-6625-2837-14 & P-7
Page 120 and 121:
Section 7 TM 11-6625-2837-14 & P-7
Page 122 and 123:
Section 7 TM 11-6625-2837-14 & P-7
Page 124 and 125:
Section 8 TM 11-6625-2837-14 & P-7
Page 126 and 127:
Section 8 TM11-6625-2837-14 & P-7 8
Page 128 and 129:
Section 8 TM 11-6625-2737-14 & P-7
Page 130 and 131:
Section 8 TM 11-6625-2837-14 & P-7
Page 132 and 133:
Section 8 TM 11-6625-2RI7-14 & P-7
Page 134 and 135:
Section 8 TM 11-6625-2837-14 & P-7
Page 136 and 137:
Section 8 TM 11-6625-2837-14-P-7 SE
Page 138 and 139:
Section 8 TM 11-6625-2837-14 & P-7
Page 140 and 141:
Section 8 TM 11-6625-2837-14 & P-7
Page 142 and 143:
Figure 8-6. System Troubleshooting
Page 144 and 145:
SERVICE SHEET 2 (Cont’d) in the d
Page 146 and 147:
Section 8 TM 11-6625-2837-14 & P-7
Page 148 and 149:
Figure 8-8. Main Troubleshooting Bl
Page 150 and 151:
Section 8 TM 11-6625-2837-14 & P-7
Page 152 and 153:
SERVICE SHEET 4 TM 11-6625-2837-14
Page 154 and 155:
Figure 8-10. A7 Mixer Assembly’s
Page 156 and 157:
SERVICE SHEET 5 TM 11-6625-2837-14
Page 158 and 159:
SERVICE SHEET 5 (Cont’d) 1 kHz so
Page 160 and 161:
Figure 8-14. Phase Modulation Secti
Page 162 and 163:
Section 8 TM 11-6625-2837-14 & P-7
Page 164 and 165:
Figure 8-16. Amplifier/Detector Sec
Page 166 and 167:
SERVICE SHEET 7 (Cont’d) a 10 dB
Page 168 and 169:
Section 8 TM 11-6625-2837-14 & P-7
Page 170 and 171:
Section 8 TM 11-6625-2837-14 & P-7
Page 172 and 173:
Figure 8-22. Attenuator Section Sch
Page 174 and 175:
SERVICE SHEET 9 (Cont’d) TM 11-66
Page 176 and 177:
Figure 8-23. A11 Logic Assembly Com
Page 178 and 179:
Section 8 TM 11-6625-2837-14 & P-7
Page 180 and 181:
Section 8 TM 11-6625-2837-14 & P-7
Page 182 and 183:
TM 11-6625-2837-14 & P-7 SECTION IX
Page 184 and 185:
Section IX TM 11-6625-2837-14 & P-7
Page 186 and 187:
Section IX TM 11-6625-2837-14 & P-7
Page 188 and 189:
D-1. General APPENDIX B MAINTENANCE
Page 190 and 191:
Allocation Chart. Subcolumns of col
Page 192 and 193:
SECTION III TOOL AND TEST EQUIPMENT
Page 195:
PIN: 049778-000
show all

TM 11-6625-2837-14&P-7 TECHNICAL MANUAL OPERATOR'S ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?