TECHNICAL SERVICE MANUAL PRIMEA LINE 2007

More documents

Recommendations

Info

Touch and Ring Multi-Way Valve Assembly REV. 00 - Mar. 07 Boiler dissipator release pump Dissipater closed Coffee filter steam multivalve drain The pressure must be released on single boiler models to reset the coffee or hot water functions. The steam will be cooled in the dissipator and released into the drip tray below thebrew unit. PRIMEA Chapter 07 15/22
7. 11 OETIKER clamp assembly and disassembly Boiler clamps Figure (1) shows the assembly position of the clamp on the boiler connector. REV. 00 - Mar. 07 BOILER Multi-way valve clamps 2 1 Multi-way valve Illustration (2) shows the assembly position of the clamp on the plastic connector of the multiway valve. A To remove the clamp, use a pincer as shown in (B) PRIMEA 2007 Chapter 07 Use suitable pliers to tighten the clamp. Ensure correct tightening (A) and positioning as shown in illustrations (1) / (2). B 16/22
Page 1 and 2:
REV. 00 - Mar. 07 TECHNICAL SERVICE
Page 3 and 4:
REV. 00 - Mar. 07 CHAPTER 1 INTRODU
Page 5 and 6:
REV. 00 - Mar. 07 CHAPTER 2 TECHNIC
Page 7 and 8:
External: Coffee bean coffee beans
Page 9 and 10:
PRIMEA 2007 Chapter 03 REV. 00 - Ma
Page 11 and 12:
Special function: Reset factory set
Page 13 and 14:
3.2 Maintenance and cleaning PRIMEA
Page 15 and 16:
PRIMEA 2007 Chapter 04 REV. 00 - Ma
Page 17 and 18: REV. 00 - Mar. 07 Primea Touch 2/6
Page 19 and 20: 4.2 Component load table Component
Page 21 and 22: REV. 00 - Mar. 07 Primea Touch /Rin
Page 23 and 24: 2 3 4 5.1 Primea Touch Plus and Tou
Page 25 and 26: 5.1.2 Microswitch and sensor check
Page 27 and 28: Total pre-ground coffee beverages
Page 29 and 30: 5.2.5 Beverage settings REV. 00 - M
Page 31 and 32: 5.2.6 System settings PRIMEA Chapte
Page 33 and 34: 5.2.8 Auto test On selection of thi
Page 35 and 36: - CAPP_DOOR_CLOSED (milk tank door
Page 37 and 38: 5.4 Ring diagnosis function Procedu
Page 39 and 40: 5.4.4 Ring product settings SYSTEM
Page 41 and 42: Applicable models: Code Brief descr
Page 43 and 44: PRIMEA Chapter 05 REV. 00 - Mar. 07
Page 45 and 46: Two factors combine to give the fiv
Page 47 and 48: The system consists of a motor-driv
Page 49 and 50: 6.3 Motor-driven tray The movement
Page 51 and 52: 6.5 SBS valve Beverage dispensing T
Page 53 and 54: PRIMEA 2007 Chapter 07 REV. 00 - Ma
Page 55 and 56: 7.2 Right-side cover PRIMEA 2007 Ch
Page 57 and 58: 7.4 Brew unit Remove the knob with
Page 59 and 60: 7.5 Electronics PRIMEA 2007 Chapter
Page 61 and 62: REV. 00 - Mar. 07 Install the brew
Page 63 and 64: 7.7 Pump Remove the silicon tube th
Page 65 and 66: REV. 00 - Mar. 07 Remove the drain
Page 67: 7.10 Multiway valve REV. 00 - Mar.
Page 71 and 72: 7.13 Grinder adjustment/assembly an
Page 73 and 74: 7.15 Autocappuccino. Withdraw the c
Page 75 and 76: Disassembling the motor-driven tray
Page 77 and 78: 8.1 Routine maintenance checklist S
Page 79: List of amendments made to manual R
show all

TECHNICAL SERVICE MANUAL PRIMEA LINE 2007

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?