TECHNICAL SERVICE MANUAL PRIMEA LINE 2007

More documents

Recommendations

Info

7.12 Coffee grinders PRIMEA 2007 Chapter 07 REV. 00 - Mar. 07 Detach the connectors from the board and remove the grinder by pulling it upwards to release slot (D) from pin (F). Ensure that the spring indicated is aligned correctly in its seat. 17/22
7.13 Grinder adjustment/assembly and disassembly Remove the coffee container and rubber seal. To remove the upper burr, rotate anticlockwise until it detaches from the bayonet coupling. PRIMEA Chapter 07 REV. 00 - Mar. 07 To remove the upper burr support, loosen the three screws as indicated, then use a hex key, turning it clockwise to release the grinder support from the bayonet coupling. On the lower burr, keep the incrementpin as indicated locked in position and proceed as shown in the figure above. When refitting the upper burr support, take care to reposition the mark as shown in the photo. 18/22
Page 1 and 2:
REV. 00 - Mar. 07 TECHNICAL SERVICE
Page 3 and 4:
REV. 00 - Mar. 07 CHAPTER 1 INTRODU
Page 5 and 6:
REV. 00 - Mar. 07 CHAPTER 2 TECHNIC
Page 7 and 8:
External: Coffee bean coffee beans
Page 9 and 10:
PRIMEA 2007 Chapter 03 REV. 00 - Ma
Page 11 and 12:
Special function: Reset factory set
Page 13 and 14:
3.2 Maintenance and cleaning PRIMEA
Page 15 and 16:
PRIMEA 2007 Chapter 04 REV. 00 - Ma
Page 17 and 18:
REV. 00 - Mar. 07 Primea Touch 2/6
Page 19 and 20: 4.2 Component load table Component
Page 21 and 22: REV. 00 - Mar. 07 Primea Touch /Rin
Page 23 and 24: 2 3 4 5.1 Primea Touch Plus and Tou
Page 25 and 26: 5.1.2 Microswitch and sensor check
Page 27 and 28: Total pre-ground coffee beverages
Page 29 and 30: 5.2.5 Beverage settings REV. 00 - M
Page 31 and 32: 5.2.6 System settings PRIMEA Chapte
Page 33 and 34: 5.2.8 Auto test On selection of thi
Page 35 and 36: - CAPP_DOOR_CLOSED (milk tank door
Page 37 and 38: 5.4 Ring diagnosis function Procedu
Page 39 and 40: 5.4.4 Ring product settings SYSTEM
Page 41 and 42: Applicable models: Code Brief descr
Page 43 and 44: PRIMEA Chapter 05 REV. 00 - Mar. 07
Page 45 and 46: Two factors combine to give the fiv
Page 47 and 48: The system consists of a motor-driv
Page 49 and 50: 6.3 Motor-driven tray The movement
Page 51 and 52: 6.5 SBS valve Beverage dispensing T
Page 53 and 54: PRIMEA 2007 Chapter 07 REV. 00 - Ma
Page 55 and 56: 7.2 Right-side cover PRIMEA 2007 Ch
Page 57 and 58: 7.4 Brew unit Remove the knob with
Page 59 and 60: 7.5 Electronics PRIMEA 2007 Chapter
Page 61 and 62: REV. 00 - Mar. 07 Install the brew
Page 63 and 64: 7.7 Pump Remove the silicon tube th
Page 65 and 66: REV. 00 - Mar. 07 Remove the drain
Page 67 and 68: 7.10 Multiway valve REV. 00 - Mar.
Page 69: 7. 11 OETIKER clamp assembly and di
Page 73 and 74: 7.15 Autocappuccino. Withdraw the c
Page 75 and 76: Disassembling the motor-driven tray
Page 77 and 78: 8.1 Routine maintenance checklist S
Page 79: List of amendments made to manual R
show all

TECHNICAL SERVICE MANUAL PRIMEA LINE 2007

Create successful ePaper yourself

Delete template?

Save as template?