- Page 1 and 2: Service Industrial Generator Sets M
- Page 3 and 4: SUBJECT PAGE SUBJECT PAGE Stator ..
- Page 5 and 6: WARNING Explosion. Can cause severe
- Page 7 and 8: Explosive fuel vapors can cause sev
- Page 9 and 10: Hazardous voltage can cause severe
- Page 11 and 12: Moving Parts WARNING Hazardous volt
- Page 14 and 15: Section 1. Specifications The spec
- Page 16 and 17: The generator set is a rotating-fie
- Page 20 and 21: Several accessories are available t
- Page 22 and 23: Audio/Visual (A/V) Alarm (with micr
- Page 24 and 25: Overvoltage Kit (with microprocesso
- Page 26: Remove Jumper if Emergency Stop is
- Page 29 and 30: 16-Light Controller (Level 1) Opera
- Page 31 and 32: 11. Low Battery Volts (if Battery C
- Page 33 and 34: Starting Local Starting Move the ge
- Page 35 and 36: Fault Shutdowns The generator set w
- Page 37 and 38: 6-Light Controller (Level 2) Operat
- Page 39 and 40: 6. Low Oil Pressure. Lamp lights if
- Page 41 and 42: Stopping Normal Stopping 1. Disconn
- Page 43 and 44: Paralleling Engine Gauge Box Contro
- Page 45 and 46: The manual controller is designed f
- Page 47 and 48: Stopping 1. Disconnect load from ge
- Page 49 and 50: Oil Requirements (30, 80, and 100 k
- Page 52 and 53: Section 4. General Troubleshooting
- Page 54 and 55: Section 5. Controller Troubleshooti
- Page 56 and 57: Circuit Board Terminal Identificati
- Page 58 and 59: Overvoltage Shutdown 120 VAC for Cr
- Page 60 and 61: Figure 5-6. Logic Schematic, 1-Phas
- Page 62 and 63: Fault Shutdowns—Microprocessor Co
- Page 64 and 65: The following text covers the manua
- Page 66: Figure 5-9. Manual Controller S-ADV
- Page 69 and 70:
Troubleshooting Microprocessor Cont
- Page 71 and 72:
Engine will not crank with generato
- Page 73 and 74:
Controller instrumentation not func
- Page 75 and 76:
Engine starts and runs, but overcra
- Page 77 and 78:
Operation Use the FASTCHECK to tes
- Page 79 and 80:
1 G-292806 1. TB1-42A 2. TB1—(See
- Page 81 and 82:
Use the following charts as a refer
- Page 83 and 84:
A Troubleshooting Manual Controller
- Page 85 and 86:
Troubleshooting Manual Controller (
- Page 87 and 88:
No output voltage is detected. 7-2
- Page 89 and 90:
This section covers generator testi
- Page 91 and 92:
7-6 Generator Troubleshooting Overv
- Page 93 and 94:
3. Observe the AC output voltmeter.
- Page 95 and 96:
Hazardous voltage can cause severe
- Page 97 and 98:
7-12 Generator Troubleshooting Auto
- Page 99 and 100:
NOTE Generator sets use a skewed (s
- Page 101 and 102:
Hot parts can cause severe injury o
- Page 103 and 104:
Follow the procedure outlined below
- Page 105 and 106:
7-20 Generator Troubleshooting Over
- Page 107 and 108:
With the constant speed type govern
- Page 109 and 110:
7-24 Generator Troubleshooting Mech
- Page 111 and 112:
7-26 Generator Troubleshooting Elec
- Page 113 and 114:
Preliminary Adjustments 1. Place ge
- Page 115 and 116:
Preliminary Adjustments 1. Place ge
- Page 117 and 118:
1 2 7-32 Generator Troubleshooting
- Page 120 and 121:
Section 8. Generator Disassembly/Re
- Page 122 and 123:
11 8 12 10 1. Voltage Regulator Ter
- Page 124 and 125:
1. Disconnect all controller-to-eng
- Page 126 and 127:
14. Place the generator assembly on
- Page 128 and 129:
7. Place the generator assembly on
- Page 130 and 131:
12. Suspend the rotor over the gene
- Page 132:
23. Install and set speed sensor ai
- Page 135 and 136:
NOTE All 12-lead generator sets are
- Page 137 and 138:
Generator Frequency Change and Adju
- Page 139 and 140:
Abbreviation Description Abbreviati
- Page 142 and 143:
TP-5353 8/94 Appendix C. Common Har
- Page 144:
Appendix D. General Torque Specific