Important Placement Instructions Enclosed See Lifting - Haas ...

More documents

Recommendations

Info

Bar Feeder Cable Routing Warning! Bar Feeder cables must be routed correctly to avoid damage. NOTE: Refer to cable labels to make sure the correct cable ends are in the proper location. 1 L1 3 L2 5 L3 1 L1 3 L2 5 L3 21 21 NC 32 NC 32 CA7 DELTA CA7 WYE DANGER! -37 -37 VECTOR 22 22 HIGH VOLTAGE! NO USER SERVICEABLE PARTS D RIVE NC 31 NC 31 INSIDE. HIGH VOLTAGE LIGHT 2 T1 4 T2 6 T3 2 T1 4 T2 6 T3 MUST BE OUT BEFORE SERVICE. CLOSED LOOP MADE IN USA TB2 240V OUT 325 VDC INPUT OUTPUT TO SERVOS 230 VAC 3 GROUND TO MOTOR + - A B C A B C 1 2 3 4 5 6 7 8 9 10 11 260-244 V 243-227 V 226-211 V 210-195 V INCOMING LINE VOLTAGE TAPS (74,75,76) DANGER!!! HIGH VOLTAGE DANGER!!! 32-1579A Alignment Plate Trough 32-1405 On ST-10/20 series it may be necessary to remove the storage tray to route the cables and gain access to the cable connecting plate. 1. Raise the charging tray to its highest position. PAgE 14 OF 66 Haas Technical Publications Installation, Application and Operator’s Manual 96-0013, Rev. BB Aug 2012 Original Instructions
2. Remove the storage tray to gain access to the Bar Feeder bracket and cable routing. 3. Feed Cable 32-1579A through the opening in the lathe side of the Bar Feeder and down through the aligment plate trough. Original Instructions Haas Technical Publications Installation, Application and Operator’s Manual Do not route cables over the side of the Bar Feeder. This will result in pinched or broken cables. Route cables under the machine using strain reliefs. x 1 x 4 96-0013, Rev. BB Aug 2012 PAgE 15 OF 66 `
Page 1: Haas Technical Publications SERVO B
Page 4 and 5: Haas Technical Publications Install
Page 6 and 7: Product: Servo Bar 300 Magazine Bar
Page 8 and 9: Lathe Preparation Spindle Liners Wh
Page 10 and 11: Lifting and Installation A t t e n
Page 12 and 13: 4. Reposition the height adjustment
Page 16 and 17: 1. Connect cable 32-1579 to the Bar
Page 18 and 19: 3. Remove the Maincon cover. 4. Add
Page 20 and 21: 1. Route the cables through the ali
Page 22 and 23: APC MTR 810 P59 SPARE3 SKIP TC MOTO
Page 24 and 25: Change Parameters 1. Power on the l
Page 26 and 27: Establish End of Bar Position 1. Pl
Page 28 and 29: Recommendations • Study and use s
Page 30 and 31: Modes of Operation The Servo Bar Fe
Page 32 and 33: Setup Transfer Tray Adjustment Any
Page 34 and 35: Machining Small Diameter Bars (.375
Page 36 and 37: 3. Tighten the clamp bolt on the ro
Page 38 and 39: 4. Handle jog the push rod up to th
Page 40 and 41: G105 [In.nnnn] [Jn.nnnn] [Kn.nnnn]
Page 42 and 43: Example 1 The following example use
Page 44 and 45: Counter The Bar Feeder can count ei
Page 46 and 47: Using the Bar 300 as a Stop The Bar
Page 48 and 49: Bar Feeder Compatibility ST / DS Mo
Page 50 and 51: Compatibility Notes • Previous ge
Page 52 and 53: 1. From the back of the Bar Feeder,
Page 54 and 55: PAgE 54 OF 66 Haas Technical Public
Page 56 and 57: SL Models - Lathe Positioning Lathe
Page 58 and 59: PAgE 58 OF 66 Haas Technical Public
Page 60 and 61: PAgE 60 OF 66 10 9 Haas Technical P
Page 62 and 63: 1. 20-6480 Rotation Control Push Ro
Page 64 and 65:
PAgE 64 OF 66 Haas Technical Public
show all

Important Placement Instructions Enclosed See Lifting - Haas ...

Create successful ePaper yourself

Delete template?

Save as template?