Important Placement Instructions Enclosed See Lifting - Haas ...

More documents

Recommendations

Info

Bar Feeder Compatibility ST / DS Models Bar Feeder Compatibility Haas Lathe Bar Feeder ST-10 / ST-10Y BAR1006ST ST-20 / ST-20Y BAR2008ST ST-20SS / ST-20SSY BAR2008ST ST-20 / ST-20Y with BB-20 BAR2010ST 2.5" (64mm) Bar Capacity Option ST-30 / ST-30Y BAR3010ST ST-30SS / ST-30SSY BAR3010SS ST-30 / ST-30Y with BB BAR3012ST 4" (102mm) Bar Capacity Option DS-30 / DS-30Y BAR2008ST DS-30SS / DS-30SSY BAR2008ST DS-30 / DS-30Y with DS-3B 3" (76mm) Bar Capacity Option BAR3010SS DS-30SS / DS-30SSY with DS-3BSS 3" (76 mm) Bar Capacity Option BAR3010SS Notes: There are no available Bar Feeders for the following lathes: OL-1, ST-40, ST-40L and all Toolroom Lathes A Bar Feeder interface is included with all new Bar Feeders. 93-BBIH – Haas Bar Feeder interface is available through the Parts Department. Kit may vary depending on current machine software. 93-BIA – Non-Haas Bar Feeder interface is available through the Parts Department. Kit may vary depending on current machine software. Chuck upgrades do not change Bar Feeder compatibility. PAgE 48 OF 66 Haas Technical Publications Installation, Application and Operator’s Manual 96-0013, Rev. BB Aug 2012 Original Instructions
GT / SL / TL (Subspindle) Models Bar Feeder Compatibility LATHE Replaced Bar Feeder New Bar Feeder and Additional (Obsolete Part Number) Parts GT-10 BARGT05B BAR1006ST • Alignment Plate (25-1026A) • LINERGT-10 KIT (1 each) • UDK5 LINER DISK KIT (1 each). • Casting Level Pad (14-2462) 4 each SL-10 BAR1006B BAR1006ST • Casting Level Pad (14-2462) 4 each SL-10BB BAR1008B BAR2008ST GT-20 • Alignment Plate (25-1026A) • Casting Level Pad (14-2462) 4 each SL-20 / TL-15 BAR2005B BAR2008ST 7K RPM Option • Alignment Plate (25-6516B) • LINER5 KIT (1 each) • OPTUDK5 LINER DISK KIT (1 each) • Casting Level Pad (14-2462) 4 each SL-20 / TL-15 BAR2008B BAR2008ST • Alignment Plate (25-6516B) • Casting Level Pad (14-2462) 4 each SL-20BB / TL-15BB BAR2010B BAR2010ST 2" Bar Capacity • Alignment Plate (25-6516B) • Casting Level Pad (14-2462) 4 each SL-30 / TL-25 BAR3010B BAR3010ST • Alignment Plate (25-6516B) • Casting Level Pad (14-2462) 4 each SL-30GB / TL-25GB BAR3010GB BAR3010ST • Alignment Plate (25-6516B) • Casting Level Pad (14-2462) 4 each SL-30BB / TL-25BB BAR3015B BAR3012ST 4" Bar Capacity • Alignment Plate (25-6516B) • Casting Level Pad (14-2462) 4 each SL-40 BAR4015B No Model Available Original Instructions Haas Technical Publications Installation, Application and Operator’s Manual 96-0013, Rev. BB Aug 2012 PAgE 49 OF 66
Page 1: Haas Technical Publications SERVO B
Page 4 and 5: Haas Technical Publications Install
Page 6 and 7: Product: Servo Bar 300 Magazine Bar
Page 8 and 9: Lathe Preparation Spindle Liners Wh
Page 10 and 11: Lifting and Installation A t t e n
Page 12 and 13: 4. Reposition the height adjustment
Page 14 and 15: Bar Feeder Cable Routing Warning! B
Page 16 and 17: 1. Connect cable 32-1579 to the Bar
Page 18 and 19: 3. Remove the Maincon cover. 4. Add
Page 20 and 21: 1. Route the cables through the ali
Page 22 and 23: APC MTR 810 P59 SPARE3 SKIP TC MOTO
Page 24 and 25: Change Parameters 1. Power on the l
Page 26 and 27: Establish End of Bar Position 1. Pl
Page 28 and 29: Recommendations • Study and use s
Page 30 and 31: Modes of Operation The Servo Bar Fe
Page 32 and 33: Setup Transfer Tray Adjustment Any
Page 34 and 35: Machining Small Diameter Bars (.375
Page 36 and 37: 3. Tighten the clamp bolt on the ro
Page 38 and 39: 4. Handle jog the push rod up to th
Page 40 and 41: G105 [In.nnnn] [Jn.nnnn] [Kn.nnnn]
Page 42 and 43: Example 1 The following example use
Page 44 and 45: Counter The Bar Feeder can count ei
Page 46 and 47: Using the Bar 300 as a Stop The Bar
Page 50 and 51: Compatibility Notes • Previous ge
Page 52 and 53: 1. From the back of the Bar Feeder,
Page 54 and 55: PAgE 54 OF 66 Haas Technical Public
Page 56 and 57: SL Models - Lathe Positioning Lathe
Page 60 and 61: PAgE 60 OF 66 10 9 Haas Technical P
Page 62 and 63: 1. 20-6480 Rotation Control Push Ro

Important Placement Instructions Enclosed See Lifting - Haas ...

Create successful ePaper yourself

Delete template?

Save as template?