S h e f f i e l d Wood Stove - Lopi

More documents

Recommendations

Info

8 Installation (for qualified installers only) Floor Protection Requirements • Stove must be placed on the included legs. Floor protection must be non-combustible and at least .018" thick (26 gauge). Min. 6” Min. 6” Min. 6” Min. 16” Minimum Minimum 37-7/8” 38-3/4” NOTE : In corner installations with reduced-clearance connector, the clearance to the wall is less than 6". In this case, floor protection must extend to the wall. Leveling Bolts Make sure these rubber tipped bolts on each leg contact the floor (they dampen any noise that may transmit through the hearth). Do not adjust with weight on the legs, the rubber tips may tear. Travis Industries 93508129 4040915
Installation (for qualified installers only) 9 Stove Placement Requirements Clearances may be reduced by methods specified in NFPA 211, listed wall shields, pipe shields, or other means approved by local building or fire officials. • Stove must be placed so that no combustibles are within, or can swing within (e.g. drapes, doors), 36" of the front of the stove • If the stove is placed in a location where the ceiling height is less than 7', it must follow the requirements in the section "Alcove Installation Requirements" • Must maintain the clearances to combustibles listed below (drywall, furniture, etc.): Clearances a d Straight Installations e b Corner Installations NOTE: Measure stove clearances to the stove top. Minimum Clearance Singlewall Reduced (See the illustration above) Connector Clearance* A Sidewall to stove 10" 10" B Backwall to stove 16-1/2" 10-1/2" C Cornerwall to stove 7-3/4" 3" D Connector to sidewall 20-1/2" 20" E Connector to backwall 15-1/2" 9" F Connector to cornerwall 15-1/2" 10-1/4" *Reduced clearance installations require one of the chimneys and connectors listed below: • DURAVENT model DVL with DURATEC chimney • DURAVENT model DVL with DURA-PLUS chimney • AMERI-TEC model DCC with model HS chimney • SECURITY model DL with SECURITY model ASHT or S2100 chimney • METAL-FAB model DW with TG chimney • GSW Double Wall Chimney Connector with Super Chimney Twenty-One • SELKIRK METALBESTOS model DS connector with model SSII chimney • I.C.C. Excel (2100-2 Can.) (103-HT USA) chimney with HP connector • Standard Masonry Chimney with any one of the above listed connectors NOTE: Standard residential installations with reduced clearance connector may use the clearance determined by the manufacturer of the connector for the connector to wall clearance or the clearance listed in this manual. Offsets must be used to maintain the stove to wall clearance. NOTE: Reduced clearance connectors may not connect to the flue collar – order an appliance adapter for the connector being used. Travis Industries 93508129 4020204 f c
Page 1 and 2: TM S h e f f i e l d Wood Stove Own
Page 3 and 4: Table of Contents 3 General Informa
Page 5 and 6: This Manual Mobile Home Safety
Page 7: Installation (for qualified install
Page 11 and 12: Installation (for qualified install
Page 13 and 14: Installation (for qualified install
Page 15 and 16: Exterior Factory Built Chimney NOTE
Page 17 and 18: Safety Notice: Operating Your Appli
Page 19 and 20: Operating Your Appliance 19 Adjusti
Page 21 and 22: Operating Your Appliance 21 Hints f
Page 23 and 24: Maintaining Your Appliance 23 Failu
Page 25 and 26: Maintaining Your Appliance 25 Yearl
Page 27 and 28: Maintaining Your Appliance 27 Fireb
Page 29 and 30: Warranty 29 To register your TRAVIS
Page 31 and 32: Optional Equipment 31 Outside Air B
Page 33 and 34: Optional Equipment 33 Rear Blower I
Page 35 and 36: Optional Equipment 35 Travis Indust

S h e f f i e l d Wood Stove - Lopi

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?