SIREC DS Display Recorder 7ND4120-xxx - Siemens

More documents

Recommendations

Info

Cables To fully comply with the requirements of the CE Mark, all cables connected to the rear of the unit should use screened cable terminated at both ends. Also a low impedance earth cable (
7. WARNING IMPROPER SIGNAL AND SUPPLY WIRING Signal and supply wiring should be kept separate. Where this is impractical, shielded cables should be used for the signal wiring. Where signal wiring is carrying, or could carry under fault conditions, hazardous voltage (defined as >30 V rms and 42.4 V peak, or >60 Vd.c.), double insulation must be used for all signal wiring. Failure to comply with these instructions could result in death or serious injury. 8. If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be inadequate. 9. In the case of portable equipment, the protective earth terminal must remain connected (even if the recorder is isolated from the mains supply) if any of the measuring, communications, or relay terminals are connected to hazardous voltages. 10. For transportation considerations, see “Instrument Care” on page 83 Hazardous Voltage Hazardous Voltages are defined by EN61010-1 as follows: WARNING HAZARDOUS VOLTAGE LEVELS Voltage levels above 30V rms and 42.4V peak or 60V dc are deemed to be "Hazardous Live". Refer to See “Appendix B - Battery Safety Data Sheet” on page 89 for further information. Failure to comply with these instructions could result in death or serious injury. Maintenance and Unit Repair See “Instrument Care” on page 83 CAUTION CONTROL UNIT DAMAGE In the event of a malfunction with the recorder contact your nearest Service Department (or authorised agent) to arrange for the return of the unit for repair. Failure to comply with these instructions may result in property damage 43-TV-25-20 GLO Issue 5 06/04 UK 3 A5E00117351-05
Page 1 and 2: s SIREC DS Display Recorder User Ma
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Password ..........................
Page 7 and 8: Appendix A - Quality Approvals 87 C
Page 9: Safety The product range of instrum
Page 13 and 14: Chapter 1: Introduction SIREC DS De
Page 15 and 16: Analogue Input card Analogue Input
Page 17 and 18: Main Features Recorder Function Rat
Page 19 and 20: Bar Digital Auto attach to trend. M
Page 21 and 22: Trend Units and Scale Scale Variabl
Page 23 and 24: Chapter 2: Installation Unpacking B
Page 25 and 26: Panel Mounting Horizontal CAUTION M
Page 27 and 28: 24Vdc Plug Connection Instructions
Page 29 and 30: Alarm Card (option) For set up of A
Page 31 and 32: Chapter 3: Quick Tour The Keypad Th
Page 33 and 34: Screen Displays There are eight dif
Page 35 and 36: Messages If a situation occurs wher
Page 37 and 38: Menu Selection Text Entry The four
Page 39 and 40: Chapter 4: General Setup Setup Edit
Page 41 and 42: Description Function: Recorder desc
Page 43 and 44: The messages screen will keep a rec
Page 45 and 46: Also entered here is the Level of t
Page 47 and 48: Protocol Protocols define the forma
Page 49 and 50: For detailed information on CJC Cal
Page 51 and 52: Chapter 5: Analogue In Setup Analog
Page 53 and 54: Input Zero Function: Value at the b
Page 55 and 56: Square Root Extraction Function: To
Page 57 and 58: Thermocouple Function: Temperature
Page 59 and 60: Select and highlight the option req
Page 61 and 62:
Chapter 6: Pen Setup Pens All avail
Page 63 and 64:
Units Function: Scale measurement u
Page 65 and 66:
Number of decades Enter a numeric v
Page 67 and 68:
Alarm - Select alarm number by high
Page 69 and 70:
Totalisers can be set up from the r
Page 71 and 72:
Min: Activated by enabling the Limi
Page 73 and 74:
Type Function: Type of logging Type
Page 75 and 76:
Chapter 7: Relay Alarm Cards Relay/
Page 77 and 78:
Chapter 8: Setup Complete Setup com
Page 79 and 80:
Chapter 9: Recording Recording NB.
Page 81 and 82:
Chapter 10: Totals Totals will not
Page 83 and 84:
Chapter 11: Change Password Changin
Page 85 and 86:
Chapter 12: Layout Layout Configura
Page 87 and 88:
Chapter 13: Software The SIREC DS r
Page 89 and 90:
System Requirements SIREC D - Viewe
Page 91 and 92:
Chapter 14: Instrument Care Battery
Page 93 and 94:
Cleaning Instructions Disk Drive Di
Page 95 and 96:
CE Mark Appendix A - Quality Approv
Page 97 and 98:
Appendix B - Battery Safety Data Sh
Page 99 and 100:
B) Fire Fighting Procedure fire. Us
Page 101 and 102:
Appendix C -Thermocouple Connection
Page 103 and 104:
External Input Reference Temperatur
Page 105 and 106:
Appendix D- Maths Expressions A mat
Page 107 and 108:
UNDER Under HI LO CJC RAV High valu
Page 109 and 110:
Ethernet E-mail Appendix E - Ethern
Page 111 and 112:
What is Fuzzy Logging? What’s it
Page 113 and 114:
Sounds Great! But what about ‘Spi
Page 115 and 116:
Appendix G - F sub 0 Sterilisation
Page 117 and 118:
Calibrate CJC - Setup Appendix H -
Page 119 and 120:
Note: If the Math option is not ava
Page 121 and 122:
CJC Adjustment Value After calibrat
Page 123 and 124:
Index 24Vdc Plug Connection instruc
Page 125 and 126:
K Battery Life ....................
Page 127 and 128:
43-TV-25-20 GLO Issue 5 06/04 UK Th
show all

SIREC DS Display Recorder 7ND4120-xxx - Siemens

Create successful ePaper yourself

Delete template?

Save as template?