Owner's Manual - Touchboards.com

More documents

Recommendations

Info

EIP-5000/5000L [8] Removing the Handle Bracket 3 1. Remove the Eleven screws from the handle bracket 3 and detach the handle bracket 3. 8-1 2 – 6 Handle Bracket 3
[9] Removing the PWB Units 1. Disconnect all the connector from the Main Unit. 2. Remove the five screws from the Main Unit. Detach the Main Unit from the PC I/F Unit. 3. Remove the two spacers from the PC I/F Unit. 4. Remove the five spacers and the screw. 5. Disconnect the PC I/F Unit from the Terminal Unit and then detach the PC I/F Unit. LSR FC4 IR (Back) Unit AD BTR TS RC FC1 FR LSUD LSRL CW BTL PR BTR TS RC FC1 LSF CW PR BTL 9-2 FR LSRL LSUD 2 – 7 FC3 FC2 FC5 TS [Enlarged] LSR FC6 FC4 FC7 RC LSL LSL FC6 9-5 RC FC7 TS FC5 FC2 FC3 LSF 9-3 9-4 Main Unit PC I/F Unit EIP-5000/5000L Terminal Unit
Page 1 and 2: TopPage SAFETY PRECAUTION IMPORTANT
Page 3 and 4: ii EIP-5000/5000L PRECAUTIONS A PRE
Page 5 and 6: UV-RADIATION PRECAUTION (Continued)
Page 7 and 8: Precautions for using lead-free sol
Page 9 and 10: [2] Operation Manual Part Names and
Page 11 and 12: Projector (Side View) Terminals Ref
Page 13 and 14: Usable Range The remote control can
Page 15 and 16: DVI digital Terminal (INPUT 3) 24 8
Page 17 and 18: [4] Maintenance Indicators Maintena
Page 19 and 20: [5] Regarding the Lamp Regarding th
Page 21 and 22: Regarding the Lamp 4 Remove the lam
Page 23 and 24: EIP-5000/5000L U/D CHAPTER 2. REMOV
Page 25 and 26: [3] Removing the Lens Hood * For EI
Page 27: [7] Removing the Top Cabinet 1. Rem
Page 31 and 32: 7. Remove the three screws from the
Page 33 and 34: [12] Removing the Filter Unit 1. Di
Page 35 and 36: EIP-5000/5000L U/D CHAPTER 3. ELECT
Page 37 and 38: No. Adjusting point Adjusting condi
Page 39 and 40: [4] SERVICE MODE 1. How to enter Se
Page 41 and 42: 9. Network setting 10. Exit from se
Page 43 and 44: EIP-5000/5000L U/D CHAPTER 4. TROUB
Page 45 and 46: Check Video signal input. Go to "Ch
Page 47 and 48: Checking the Main unit. Check outpu
Page 49 and 50: Checking the Terminal unit. Check i
Page 51 and 52: 1 2 3 Checking the RGB input Feed t
Page 53 and 54: RGB signal check Is the Signal Type
Page 55 and 56: 4 Component input (except 408i) che
Page 57 and 58: VIDEO sync signal check Measure TL8
Page 59 and 60: — MEMO — 4 - 17 EIP-5000/5000L
Page 61 and 62: k B+12VM B+5VM B+3V3AT IC26/27/ 28/
Page 63 and 64: Overall wiring diagram ermal nsor D
Page 65 and 66: 11 12 13 14 15 16 17 18 19 6 - 2 EI
Page 67 and 68: 11 12 13 14 15 16 17 18 19 6 - 4 EI
Page 69 and 70: J I H G F E D C B A FORMATTER Unit
Page 71 and 72: J I H G F E D C B A POWER Unit (Sid
Page 73 and 74: J I H G F E D C B A FILTER Unit (Si
Page 75 and 76: J I H G F E D C B A PC I/F Unit (Si
Page 77 and 78: [7] AUDIO Unit J I H G F E D C B A
Page 79 and 80:
J I H G F E D C B A KEYPAD Unit (Si
Page 81 and 82:
[10] IR (FRONT)/IR (REAR)/LAMP1 COV
Page 83 and 84:
EIP-5000/5000L U/D CHAPTER 8. SCHEM
Page 85 and 86:
PartsGuide [1] PRINTED WIRING BOARD
Page 87 and 88:
NO. PARTS CODE [2] 9NK5600600363 (M
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
NO. PARTS CODE [3] 9NK5600600498 (F
Page 103 and 104:
NO. PARTS CODE [4] 9NK5600204367 (P
Page 105 and 106:
NO. PARTS CODE [5] 9NK5600204350 (F
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
NO. PARTS CODE [11] 9NK5600204319 (
Page 119 and 120:
NO. PARTS CODE [11] 9NK5600204319 (
Page 121 and 122:
NO. PARTS CODE [14] 9NK5600204260 (
Page 123 and 124:
[19] CABINET AND MECHANICAL PARTS (
Page 125 and 126:
[21] CABINET AND MECHANICAL PARTS (
Page 127 and 128:
NO. PARTS CODE [22] CABINET AND MEC
Page 129 and 130:
NO. PARTS CODE [22] CABINET AND MEC
Page 131 and 132:
NO. PARTS CODE [23] OPTICAL MECHANI
Page 133 and 134:
[25] PACKING PARTS (NOT REPLACEMENT
show all

Owner's Manual - Touchboards.com

Create successful ePaper yourself

Delete template?

Save as template?