Owner's Manual - Touchboards.com

More documents

Recommendations

Info

EIP-5000/5000L 4. Adjustment of video 5. Others 6. Initialization of adjustment value 7. Internal test pattern 8. Firmware version 1. Feed a video signal 2. Select the group "VIDEO" EIP-5000 will change to input4 mode automatically group Subject initial value effective range adjustment source/mode adjustment of VIDEO VIDEO PICTURE 0 ±60 contrast INPUT4 / video picture BRIGHT 0 ±60 brightness INPUT4 / video adjustment of VIDEO TINT 0 ±120 tint (effected in NTSC only) INPUT4 / video color N-COLOR 0 ±120 color saturation INPUT4 / video setting of VIDEO gain control AGC-CNT 0-1 auto gain control INPUT4 / video 0 : AGC On 1 : AGC Off adjustment of delay DLY 0 ±5 INPUT4 / video between chroma and luminance adjustment of VIDEO horizontal position H-CENTER 0 ±10 INPUT4 / video adjustment of VIDEO low pass filter FILTER 0 ±3 filter gain INPUT4 / video switch of component low pass filter group Subject initial value effective range adjustment source/mode VIDEO COMP-FILTER 0 0-1 0 : filter off, 1 : filter on INPUT1 / component switch of RGB low pass filter RGB-FILTER 0 0-1 0 : filter off, 1 : filter on INPUT1 / RGB switch of audio delay of internal speaker A-DELAY 0 0-1 0 : delay on, 1 : delay off INPUT4 / video RESET - Select this item and push ENTER key. Value inside each item of "DLP", "DLPV" and "VIDEO" is returned to the initial value with RESET. group Subject initial value effective range signal PATTERN RGB 1 1-8 raster signal RGB[50] 1 1-8 50% raster signal CROSS 1 1-9 cross hatch FOCUS 1 1-2 checkered signal STEP 1 1-2 8step/16step COLOR color bar CHR 1 1-4 oblique line and vertical line group Subject version FIRMWARE SUB *.** MAIN-LOADER *.** MAIN-ZIMAGE *.** MAIN-MTD *.** MAIN-JFFS *.** 3 – 6
9. Network setting 10. Exit from service mode [5] Failure mode when the lamp does not light up even when powered on 1. Status of LED • POWER does not light up. The sub CPU (IC3603) does not start. Check the peripheral circuits. • POWER blinks in red. • LAMP LED blinks in red. 2. Checking the status via RS232C serial communication 3. Others group Subject address NETWORK IP ADDRESS 192.168.150.002 MAC ADDRESS **:**:**:**:**:** group EXIT - Select this item and push ENTER key. • The lamp does not light up if the color wheel motor does not run. • The lamp does not light up if the thermistor sensor is not connected (e.g. breaking of wire). • The lamp does not light up when if a communication error occurs between IC8003 and IC8025 on the PC board. 3 – 7 EIP-5000/5000L 0.5-second interval: Fan error detection. (This unit detects the number of fan revolutions. When the fan is running more slowly than the preset lower speed limit, the power is shut down by the protection function even if the fan does not stop completely.) 1-second interval: Bottom air filter cover (RCS) detection. 2-second interval: Communication error between sub CPU (IC3603) and main CPU (IC8003). 1-second interval: Lamp leaf switch detection. (The power is not turned on if the lamp cartridge is removed from the unit.) Send "TFCK 1" + ENTER, "TABN 1" via 232C communication to check the status of the projector. Return value example of the normal unit TFCK 1 [ RCS ] Close [ Lamp1 Leaf ] Close [ Lamp2 Leaf ] Close [ Main-Sub ] Communication OK. [ Fan ] Normal [ pwm Fan1] No error [ pwm Fan2] No error [ pwm Fan3] No error [ pwm Fan4] No error [ pwm Fan5] No error [ pwm Fan6] No error [ dac Fan0] No error [ dac Fan1] No error [ Temperature ] Normal [ Lamp1 Non Light ] Normal [ Lamp2 Non Light ] Normal [ Lamp Life1 ] Normal [ Lamp Life2 ] Normal OK
Page 1 and 2: TopPage SAFETY PRECAUTION IMPORTANT
Page 3 and 4: ii EIP-5000/5000L PRECAUTIONS A PRE
Page 5 and 6: UV-RADIATION PRECAUTION (Continued)
Page 7 and 8: Precautions for using lead-free sol
Page 9 and 10: [2] Operation Manual Part Names and
Page 11 and 12: Projector (Side View) Terminals Ref
Page 13 and 14: Usable Range The remote control can
Page 15 and 16: DVI digital Terminal (INPUT 3) 24 8
Page 17 and 18: [4] Maintenance Indicators Maintena
Page 19 and 20: [5] Regarding the Lamp Regarding th
Page 21 and 22: Regarding the Lamp 4 Remove the lam
Page 23 and 24: EIP-5000/5000L U/D CHAPTER 2. REMOV
Page 25 and 26: [3] Removing the Lens Hood * For EI
Page 27 and 28: [7] Removing the Top Cabinet 1. Rem
Page 29 and 30: [9] Removing the PWB Units 1. Disco
Page 31 and 32: 7. Remove the three screws from the
Page 33 and 34: [12] Removing the Filter Unit 1. Di
Page 35 and 36: EIP-5000/5000L U/D CHAPTER 3. ELECT
Page 37 and 38: No. Adjusting point Adjusting condi
Page 39: [4] SERVICE MODE 1. How to enter Se
Page 43 and 44: EIP-5000/5000L U/D CHAPTER 4. TROUB
Page 45 and 46: Check Video signal input. Go to "Ch
Page 47 and 48: Checking the Main unit. Check outpu
Page 49 and 50: Checking the Terminal unit. Check i
Page 51 and 52: 1 2 3 Checking the RGB input Feed t
Page 53 and 54: RGB signal check Is the Signal Type
Page 55 and 56: 4 Component input (except 408i) che
Page 57 and 58: VIDEO sync signal check Measure TL8
Page 59 and 60: — MEMO — 4 - 17 EIP-5000/5000L
Page 61 and 62: k B+12VM B+5VM B+3V3AT IC26/27/ 28/
Page 63 and 64: Overall wiring diagram ermal nsor D
Page 65 and 66: 11 12 13 14 15 16 17 18 19 6 - 2 EI
Page 67 and 68: 11 12 13 14 15 16 17 18 19 6 - 4 EI
Page 69 and 70: J I H G F E D C B A FORMATTER Unit
Page 71 and 72: J I H G F E D C B A POWER Unit (Sid
Page 73 and 74: J I H G F E D C B A FILTER Unit (Si
Page 75 and 76: J I H G F E D C B A PC I/F Unit (Si
Page 77 and 78: [7] AUDIO Unit J I H G F E D C B A
Page 79 and 80: J I H G F E D C B A KEYPAD Unit (Si
Page 81 and 82: [10] IR (FRONT)/IR (REAR)/LAMP1 COV
Page 83 and 84: EIP-5000/5000L U/D CHAPTER 8. SCHEM
Page 85 and 86: PartsGuide [1] PRINTED WIRING BOARD
Page 87 and 88: NO. PARTS CODE [2] 9NK5600600363 (M
Page 89 and 90: NO. PARTS CODE [2] 9NK5600600363 (M
Page 91 and 92:
NO. PARTS CODE [2] 9NK5600600363 (M
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
NO. PARTS CODE [3] 9NK5600600498 (F
Page 103 and 104:
NO. PARTS CODE [4] 9NK5600204367 (P
Page 105 and 106:
NO. PARTS CODE [5] 9NK5600204350 (F
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
NO. PARTS CODE [11] 9NK5600204319 (
Page 119 and 120:
NO. PARTS CODE [11] 9NK5600204319 (
Page 121 and 122:
NO. PARTS CODE [14] 9NK5600204260 (
Page 123 and 124:
[19] CABINET AND MECHANICAL PARTS (
Page 125 and 126:
[21] CABINET AND MECHANICAL PARTS (
Page 127 and 128:
NO. PARTS CODE [22] CABINET AND MEC
Page 129 and 130:
NO. PARTS CODE [22] CABINET AND MEC
Page 131 and 132:
NO. PARTS CODE [23] OPTICAL MECHANI
Page 133 and 134:
[25] PACKING PARTS (NOT REPLACEMENT
show all

Owner's Manual - Touchboards.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?