Owner's Manual - Touchboards.com

More documents

Recommendations

Info

EIP-5000/5000L OSD check Is the user menu normally displayed with the MENU key? NO Enter the process menu to select PATTERN. Select the COLOR pattern. YES OSD is normal. Is the OSD display color normal? NO Adjust the DLP system with the process adjustment. Select the STEP signal. YES Is the STEP signal normal? YES Rewrite the OSD data. NO Are signals suitable for STEP signals sent to TL8047, 8048 and 8049? YES Go to "Checking the periphery of GA5". Rewrite the OSD data. NO IC8025 is defective. 4 – 8 0 0
1 2 3 Checking the RGB input Feed the sync separation analog RGB signal to INPUT1. Select INPUT1 by using the panel key or remote control. Is a picture displayed? NO Go to "Video input check". YES Is a picture distorted? YES Go to "Checking of sync signal". NO Are three colors (R, G and B) displayed? NO Go to "RGB signal check". Perform AUTOSYNC. YES Is the contour displayed properly? NO IC8017 or the periphery of IC8025 is defective. YES Are vertical stripe patterns distorted? YES IC8017 or the periphery of IC8025 is defective. End Video input check Go to "Input signal setting check". NO Is a video signal applied to the land of C8165? NO Is signal applied to the pin 13 of SC8001 (B to B connector)? YES YES Go to "Checking the sync signal". The signal path is defective. Check CRs from SC8001 to IC8017. IC8025 or IC8017 is defective. 4 – 9 EIP-5000/5000L NO The signal source or connector is defective.
Page 1 and 2: TopPage SAFETY PRECAUTION IMPORTANT
Page 3 and 4: ii EIP-5000/5000L PRECAUTIONS A PRE
Page 5 and 6: UV-RADIATION PRECAUTION (Continued)
Page 7 and 8: Precautions for using lead-free sol
Page 9 and 10: [2] Operation Manual Part Names and
Page 11 and 12: Projector (Side View) Terminals Ref
Page 13 and 14: Usable Range The remote control can
Page 15 and 16: DVI digital Terminal (INPUT 3) 24 8
Page 17 and 18: [4] Maintenance Indicators Maintena
Page 19 and 20: [5] Regarding the Lamp Regarding th
Page 21 and 22: Regarding the Lamp 4 Remove the lam
Page 23 and 24: EIP-5000/5000L U/D CHAPTER 2. REMOV
Page 25 and 26: [3] Removing the Lens Hood * For EI
Page 27 and 28: [7] Removing the Top Cabinet 1. Rem
Page 29 and 30: [9] Removing the PWB Units 1. Disco
Page 31 and 32: 7. Remove the three screws from the
Page 33 and 34: [12] Removing the Filter Unit 1. Di
Page 35 and 36: EIP-5000/5000L U/D CHAPTER 3. ELECT
Page 37 and 38: No. Adjusting point Adjusting condi
Page 39 and 40: [4] SERVICE MODE 1. How to enter Se
Page 41 and 42: 9. Network setting 10. Exit from se
Page 43 and 44: EIP-5000/5000L U/D CHAPTER 4. TROUB
Page 45 and 46: Check Video signal input. Go to "Ch
Page 47 and 48: Checking the Main unit. Check outpu
Page 49: Checking the Terminal unit. Check i
Page 53 and 54: RGB signal check Is the Signal Type
Page 55 and 56: 4 Component input (except 408i) che
Page 57 and 58: VIDEO sync signal check Measure TL8
Page 59 and 60: — MEMO — 4 - 17 EIP-5000/5000L
Page 61 and 62: k B+12VM B+5VM B+3V3AT IC26/27/ 28/
Page 63 and 64: Overall wiring diagram ermal nsor D
Page 65 and 66: 11 12 13 14 15 16 17 18 19 6 - 2 EI
Page 67 and 68: 11 12 13 14 15 16 17 18 19 6 - 4 EI
Page 69 and 70: J I H G F E D C B A FORMATTER Unit
Page 71 and 72: J I H G F E D C B A POWER Unit (Sid
Page 73 and 74: J I H G F E D C B A FILTER Unit (Si
Page 75 and 76: J I H G F E D C B A PC I/F Unit (Si
Page 77 and 78: [7] AUDIO Unit J I H G F E D C B A
Page 79 and 80: J I H G F E D C B A KEYPAD Unit (Si
Page 81 and 82: [10] IR (FRONT)/IR (REAR)/LAMP1 COV
Page 83 and 84: EIP-5000/5000L U/D CHAPTER 8. SCHEM
Page 85 and 86: PartsGuide [1] PRINTED WIRING BOARD
Page 87 and 88: NO. PARTS CODE [2] 9NK5600600363 (M
Page 101 and 102:
NO. PARTS CODE [3] 9NK5600600498 (F
Page 103 and 104:
NO. PARTS CODE [4] 9NK5600204367 (P
Page 105 and 106:
NO. PARTS CODE [5] 9NK5600204350 (F
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
NO. PARTS CODE [11] 9NK5600204319 (
Page 119 and 120:
NO. PARTS CODE [11] 9NK5600204319 (
Page 121 and 122:
NO. PARTS CODE [14] 9NK5600204260 (
Page 123 and 124:
[19] CABINET AND MECHANICAL PARTS (
Page 125 and 126:
[21] CABINET AND MECHANICAL PARTS (
Page 127 and 128:
NO. PARTS CODE [22] CABINET AND MEC
Page 129 and 130:
NO. PARTS CODE [22] CABINET AND MEC
Page 131 and 132:
NO. PARTS CODE [23] OPTICAL MECHANI
Page 133 and 134:
[25] PACKING PARTS (NOT REPLACEMENT
show all

Owner's Manual - Touchboards.com

Create successful ePaper yourself

Delete template?

Save as template?