Owner's Manual - Touchboards.com
Owner's Manual - Touchboards.com
Owner's Manual - Touchboards.com
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
EIP-5000/5000L<br />
No. Adjusting point Adjusting conditions Adjusting procedure<br />
1. After signal input, select COMPO-AUTO for automatic adjustment.<br />
6 Adjustment of<br />
<strong>com</strong>ponent Cr/<br />
Cb offset (1)<br />
7 Adjustment of<br />
<strong>com</strong>ponent<br />
brightness<br />
8 Adjustment of<br />
<strong>com</strong>ponent Cr/<br />
Cb offset (2)<br />
9 Adjustment of<br />
RGB white balance<br />
10 Adjustment of<br />
sRGB white balance<br />
11 adjustment of<br />
video white balance<br />
12 Adjustment of<br />
DTV white balance<br />
for reference / setting<br />
1. Feed the color difference signal<br />
(480i) to INPUT1<br />
: Y 0% brightness, Cb and Cr 0%<br />
white patterns.<br />
2. Select the following group and<br />
subject.<br />
Group : COMPO<br />
Subject : COMPO-AUTO<br />
1. Feed the color difference signal<br />
(480i) to INPUT1<br />
: Y 0% brightness, Cb and Cr 0%<br />
white patterns.<br />
2. Select the following group and<br />
subject.<br />
Group : COMPO<br />
Subject : G-BRIGHT<br />
1. Feed the color difference signal<br />
(480i) to INPUT1<br />
: Y 0% brightness, Cb and Cr 0%<br />
white patterns.<br />
2. Select the following group and<br />
subject.<br />
Group : COMPO<br />
Subject : CR-OFFSET<br />
1. Feed the 50% gray pattern signal<br />
(XGA, 60 Hz) to INPUT1.<br />
2. Select the following group and<br />
subject.<br />
Group : DLP<br />
Subjects : R1-GAIN (Red)<br />
B1-GAIN (Blue)<br />
1. Feed the 50% gray pattern signal<br />
(XGA, 60 Hz) to INPUT1<br />
2. Select the following group and<br />
subject.<br />
Group : DLP<br />
Subjects : S-G1-GAIN (Green)<br />
S-B1-GAIN (Blue)<br />
1. Feed the 50% gray pattern signal<br />
(NTSC, burst signal) to INPUT4.<br />
2. Select the following group and<br />
subject.<br />
Group : DLPV<br />
Subjects : V-R1-GAIN (Red)<br />
V-B1-GAIN (Blue)<br />
1. Feed the 50% gray pattern signal<br />
(480i, color difference signal) to<br />
INPUT1.<br />
2. Select the following group and<br />
subject.<br />
Group : DLPV<br />
Subjects : C-R1-GAIN (Red)<br />
C-B1-GAIN (Blue)<br />
13 Factory settings 1. Select the following group and<br />
subject.<br />
Group : SSS<br />
Subject : S3 (Worldwide/Korea)<br />
S5 (Japan)<br />
OSD language Video-set up level<br />
S3 English 0IRE<br />
(S4) English 7.5IRE<br />
S5 Japanese 0IRE<br />
1. Make adjustment so that some bits should be missing in the picture.<br />
* refer to the following photo image<br />
1. Reduce the CR-OFFSET value by 2 points.<br />
1. Adjust R1-GAIN and B1-GAIN so that x-value should be 290 ±3 and yvalue<br />
310 ± 3.<br />
1. Adjust S-G1-GAIN and S-B1-GAIN so that x-value should be 313 ±5 and yvalue<br />
329 ± 5.<br />
1. Adjust V-R1-GAIN and V-B1-GAIN so that x-value should be 290 ± 3 and y-<br />
value should be 310 ± 3.<br />
1. Adjust C-R1-GAIN and C-B1-GAIN so that x-value should be 290 ± 3 and yvalue<br />
should be 310 ± 3.<br />
1. Make the following settings.<br />
: S5 (to Japan)<br />
: S3 (to Worldwide/Korea)<br />
3 – 2