use of metal templates for microcavity formation in alumina

More documents

Recommendations

Info

We approve the thesis of Sırma BALKAN ___________________________ Prof. Dr. Sedat AKKURT Supervisor ___________________________ Prof. Dr. Muhsin ÇİFTÇİOĞLU Committee Member ___________________________ Prof. Dr. Fehime ÖZKAN Committee Member 19 December 2011 ___________________________ ________________________ Assoc. Prof. Dr. Mustafa M. DEMİR Prof. Dr. R. Tuğrul SENGER Head of the Department of Materials Dean of the Graduate School of Science and Engineering Engineering and Sciences
ACKNOWLEDGEMENTS I would like to express the Materials Science and Engineering Department at Izmir Institute of Technology for accepting me into their program and giving me the opportunity to attain an M.S degree in this field. I deeply thank my advisor Prof.Dr. Sedat Akkurt for his supervision, support and help during my studies. I would like to thank to Dr. Emre Yalamaç for his help and support. I would like to thank the IYTE - MAM and the technical staff for their help during the analysis of the study. I would like to thank to Prof. Dr. Claude Paul Carry, Dr. Audrey Guyon and the technical staff in SIMaP Laboratory in Grenoble, France and for their help, patience and friendship during the dilatometric works. My special thanks go to my entire family for their support, tolerance and understanding throughout the years.
Page 1: USE OF METAL TEMPLATES FOR MICROCAV
Page 5 and 6: ÖZET ALÜMİNA İÇİNDE MİKROBO
Page 7 and 8: 4.3.1. Alumina ....................
Page 9 and 10: Figure 3.4. Pressed samples: (a) be
Page 11 and 12: Figure 4.35. Phase equilibrium diag
Page 13 and 14: CHAPTER 1 INTRODUCTION Porous oxide
Page 15 and 16: 2.1. Porous Materials CHAPTER 2 LIT
Page 17 and 18: Alumina ceramic is one of the most
Page 19 and 20: 2.3. Properties and Applications of
Page 21 and 22: Selection of stainless steels based
Page 23 and 24: Some physical properties of copper
Page 25 and 26: of some of the oxygen from the air
Page 27 and 28: not occupied by the flow of Cu from
Page 29 and 30: During the 4 hours soaking time at
Page 31 and 32: y the technique of dilatometry (Rah
Page 33 and 34: CHAPTER 3 EXPERIMENTAL In this chap
Page 35 and 36: Table 3.1. Properties of alumina po
Page 37 and 38: 3.2.1. Co-Pressing with Single-acti
Page 39 and 40: 3.3. Density Measurements The final
Page 41 and 42: Figures 4.3 and 4.4 show relative d
Page 43 and 44: Densification Rate (1/ o C) 0,005 0
Page 45 and 46: Densification Rate (1/ o C) 0,009 0
Page 47 and 48: (a) (b) (c) (d) (e) Figure 4.8. SEM
Page 49 and 50: Figure 4.10. EDS analysis of the Ti
Page 51 and 52: 4.3.3. Ti Diffusion into Alumina In
Page 53 and 54:
Titanium advanced through alumina a
Page 55 and 56:
Wt (%) Wt (%) 100 80 60 40 20 0 100
Page 57 and 58:
Figure 4.22. EDS line analysis of t
Page 59 and 60:
Densification Rate (1/ o C) 0,0069
Page 61 and 62:
Figure 4.27, 28 and 29 belong to ED
Page 63 and 64:
4.3.5. Stainless Steel Diffusion in
Page 65 and 66:
Wt (%) 50 45 40 35 30 25 20 15 10 5
Page 67 and 68:
Wt (%) 70 60 50 40 30 20 10 0 Al (w
Page 69 and 70:
4.3.7. Results of Sintering of Alum
Page 71 and 72:
Wt (%) 40 35 30 25 20 15 10 5 0 Al
Page 73 and 74:
CHAPTER 5 CONCLUSIONS Densification
Page 75 and 76:
REFERENCES Alcoa, Inc., 2010, Alumi
Page 77 and 78:
Isobe, T., Tomital, T., Kameshima,
Page 79:
Yalamaç, E., 2010, Sintering, Co-S
show all

use of metal templates for microcavity formation in alumina

Create successful ePaper yourself

Delete template?

Save as template?