Operating Instructions Dplmagic Marker Dplgenesis ... - ACI Laser

More documents

Recommendations

Info

This product conforms to the requirements of the Machinery Directive 98/37/ EU (Machine regulations 9.GSGV). The CE symbol is located on the type plate. Manufacturer ACI Laser GmbH Österholzstraße 9 D-99428 Nohra Germany Phone: +49 3643 4152-0 Fax: +49 3643 4152-77 Internet: www.ACI-Laser.de e-mail: info@ACI-Laser.de We are constantly working on further developments. Therefore, please understand that we must reserve the right to change the scope of the delivery in respect of the form, equipment and technology at any time. Reprinting, copying or translating this document in whole or in part is forbidden without the express written permission of ACI Laser GmbH! All rights under the copyright laws are expressly reserved by ACI Laser GmbH. The manufacturer shall only be responsible for the safety characteristics of this device within the scope of the legally applicable regulations if it is operated by the user in accordance with the operating instructions and repaired by ACI Laser GmbH itself or someone appointed by and acting under the instructions of ACI Laser GmbH. Last update: 08/2006 © ACI Laser GmbH
Table of Contents 1 Introduction ...................................................................................... 5 2 Important Information...................................................................... 5 2.1 Intended Use..................................................................................... 6 2.2 Improper Use .................................................................................... 6 2.3 Symbols in the Document ............................................................... 7 Warning notes................................................................................ 7 Additional symbols ......................................................................... 7 Warning Notices on the Device...................................................... 8 Type plate ...................................................................................... 9 2.4 Basic Safety Instructions .............................................................. 10 Laser class................................................................................... 10 General Information ..................................................................... 11 Initial operation............................................................................. 12 Operation ..................................................................................... 12 Maintenance/Care........................................................................ 12 3 Brief Description ............................................................................ 13 3.1 View of device ................................................................................ 13 3.2 Intended purpose ........................................................................... 13 3.3 Principle of Operation.................................................................... 14 Laser beam source ...................................................................... 14 Shutter ......................................................................................... 14 Pilot laser ..................................................................................... 14 Beam deflection ........................................................................... 14 Laser electronics.......................................................................... 14 3.4 Unpacking....................................................................................... 15 Scope of delivery ......................................................................... 15 3.5 Mechanical Installation.................................................................. 16 Assembly ..................................................................................... 16 Swivelling the scan unit................................................................ 16 Focussing..................................................................................... 17 3.6 Installing the Marking Software .................................................... 18 Minimum hardware requirements ................................................ 18 Installation.................................................................................... 18 3.7 Electrical Installation ..................................................................... 19 3.7.1 Interfaces ........................................................................................ 19 Laser control interface ................................................................. 19 Optional trim-module.................................................................... 21 3.7.2 Connection ...................................................................................... 22 Power connection ........................................................................ 22 Connection with the PC ............................................................... 22 Operating Instructions DPLMagic/Genesis/Nexus Marker -08/2006 1
Page 1: Operating Instructions DPLMagic Mar
Page 5 and 6: Table of Contents 13.2.5 Laser Cont
Page 7 and 8: 1 Introduction 2 Important Informat
Page 9 and 10: 2.3 Symbols in the Document Warning
Page 11 and 12: Important Information Type plate Th
Page 13 and 14: Important Information General Infor
Page 15 and 16: 3 Brief Description 3.1 View of dev
Page 17 and 18: 3.4 Unpacking Brief Description The
Page 19 and 20: Brief Description Focussing NOTE! A
Page 21 and 22: 3.7 Electrical Installation 3.7.1 I
Page 23 and 24: Brief Description Connections for o
Page 25 and 26: 4 Initial operation 4.1 Checking th
Page 27 and 28: 5 Operation Operation All operating
Page 29 and 30: Care objective. In so doing, draw t
Page 31 and 32: 9 Fault Finding 9.1 General Faults
Page 33 and 34: Status/Error Trigger Message LoopSt
Page 35 and 36: 12 Technical Data Laser device Diod
Page 37 and 38: 13 Detailed Advanced Information De
Page 39 and 40: 13.2.1 Laser beam source 1 E[ev] E
Page 41 and 42: 13.2.4 Plane field objective Detail
Page 43 and 44: 13.2.6 Marking Software Detailed Ad
Page 45 and 46: 13.3.1 Pulse Power Density Detailed
Page 47 and 48: Principle of operation of a Peltier
Page 49 and 50: 13.5.1 Pulse Overlapping Detailed A
Page 51 and 52: Detailed Advanced Information Plast
Page 53 and 54:
14.2 Technical drawing M6 x10 deep
Page 55 and 56:
15 Index Index A Additional symbols
Page 57 and 58:
Index O Objective .................
Page 60:
08/2006 - Marker DPLMagic/Genesis/N
show all

Operating Instructions Dplmagic Marker Dplgenesis ... - ACI Laser

Create successful ePaper yourself

Delete template?

Save as template?