Operating Instructions Dplmagic Marker Dplgenesis ... - ACI Laser

More documents

Recommendations

Info

Scrap Disposal 8 Scrap Disposal ENVIRONMENTAL PROTECTION! For a small fee, the customer will accept return of the laser device and dispose of it properly in a manner that is environmentally compatible. Environmentally sensible disposal of electrical and electronic equipment! Electrical and electronic equipment contains valuable materials that should be supplied to recycling or recovery. Please dispose of electrical and electronic equipment at qualified collecting points separate from municipal waste. 28 Operating Instructions DPLMagic/Genesis/Nexus Marker - 08/2006
9 Fault Finding 9.1 General Faults Problem/Fault Possible cause Elimination Error message when loading the marking software Marking software incorrectly installed USB cable not connected properly Laser will not start USB cable not connected properly Reinstall the software. Fault Finding Check whether the cable is plugged in correctly. No supply voltage Check whether your laser is supplied with power. Check whether the cable is plugged in correctly. No laser beam Shutter closed Check whether all safety switches are locked. Check whether the shutter is opened in your marking job. Defocusing Check the focus position by changing the distance between focusing objective and work piece. Incorrect laser parameters Check your laser parameters, they may not be suitable for the work piece to be marked. Laser power too low Defocusing Check the focus position by changing the distance between focusing objective and work piece. Incorrect laser parameters Laser does not pulse Incorrect laser parameters Laser switches off automatically Environmental conditions do not meet the specifications Check your laser parameters, they may not be suitable for the work piece to be marked. Check the laser parameter settings, the laser may be working in cw operation. Check the environmental conditions. Keep to the environmental conditions required. NOTE! Please contact our Technical Customer Service in the first instance if the fault cannot be eliminated as described above. Operating Instructions DPLMagic/Genesis/Nexus Marker -08/2006 29
Page 1 and 2: Operating Instructions DPLMagic Mar
Page 3 and 4: Table of Contents 1 Introduction ..
Page 5 and 6: Table of Contents 13.2.5 Laser Cont
Page 7 and 8: 1 Introduction 2 Important Informat
Page 9 and 10: 2.3 Symbols in the Document Warning
Page 11 and 12: Important Information Type plate Th
Page 13 and 14: Important Information General Infor
Page 15 and 16: 3 Brief Description 3.1 View of dev
Page 17 and 18: 3.4 Unpacking Brief Description The
Page 19 and 20: Brief Description Focussing NOTE! A
Page 21 and 22: 3.7 Electrical Installation 3.7.1 I
Page 23 and 24: Brief Description Connections for o
Page 25 and 26: 4 Initial operation 4.1 Checking th
Page 27 and 28: 5 Operation Operation All operating
Page 29: Care objective. In so doing, draw t
Page 33 and 34: Status/Error Trigger Message LoopSt
Page 35 and 36: 12 Technical Data Laser device Diod
Page 37 and 38: 13 Detailed Advanced Information De
Page 39 and 40: 13.2.1 Laser beam source 1 E[ev] E
Page 41 and 42: 13.2.4 Plane field objective Detail
Page 43 and 44: 13.2.6 Marking Software Detailed Ad
Page 45 and 46: 13.3.1 Pulse Power Density Detailed
Page 47 and 48: Principle of operation of a Peltier
Page 49 and 50: 13.5.1 Pulse Overlapping Detailed A
Page 51 and 52: Detailed Advanced Information Plast
Page 53 and 54: 14.2 Technical drawing M6 x10 deep
Page 55 and 56: 15 Index Index A Additional symbols
Page 57 and 58: Index O Objective .................
Page 60: 08/2006 - Marker DPLMagic/Genesis/N

Operating Instructions Dplmagic Marker Dplgenesis ... - ACI Laser

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?